manualshive.com logo in svg

Cisco Catalyst 3130, Руководство по настройке программного обеспечения

Cisco Catalyst 3130 - сетевой коммутатор с широкими возможностями управления и конфигурации. Пользователи могут загрузить бесплатное руководство по настройке программного обеспечения с официального сайта. Настройте свою сеть с легкостью, следуя инструкциям в Software Configuration Manual для Catalyst 3130. Более подробную информацию можно найти на manualshive.com.

Поделиться
Скачать
background image

 

17-6

Cisco Catalyst Blade Switch 3130 and 3032 for Dell Software Configuration Guide

OL-12247-04

Chapter 17      Configuring IEEE 802.1Q and Layer 2 Protocol Tunneling

Configuring IEEE 802.1Q Tunneling

IEEE 802.1Q Tunneling and Other Features

Although IEEE 802.1Q tunneling works well for Layer 2 packet switching, there are incompatibilities 
between some Layer 2 features and Layer 3 switching.

•

A tunnel port cannot be a routed port.

•

IP routing is not supported on a VLAN that includes IEEE 802.1Q ports. Packets received from a 
tunnel port are forwarded based only on Layer 2 information. If routing is enabled on a switch 
virtual interface (SVI) that includes tunnel ports, untagged IP packets received from the tunnel port 
are recognized and routed by the switch. Customer can access the internet through its native VLAN. 
If this access is not needed, you should not configure SVIs on VLANs that include tunnel ports.

•

Fallback bridging is not supported on tunnel ports. Because all IEEE 802.1Q-tagged packets 
received from a tunnel port are treated as non-IP packets, if fallback bridging is enabled on VLANs 
that have tunnel ports configured, IP packets would be improperly bridged across VLANs. 
Therefore, you must 

not

 enable fallback bridging on VLANs with tunnel ports.

•

Tunnel ports do not support IP access control lists (ACLs). 

•

Layer 3 quality of service (QoS) ACLs and other QoS features related to Layer 3 information are 
not supported on tunnel ports. MAC-based QoS is supported on tunnel ports. 

•

EtherChannel port groups are compatible with tunnel ports as long as the IEEE 802.1Q 
configuration is consistent within an EtherChannel port group. 

•

Port Aggregation Protocol (PAgP), Link Aggregation Control Protocol (LACP), and UniDirectional 
Link Detection (UDLD) are supported on IEEE 802.1Q tunnel ports.

•

Dynamic Trunking Protocol (DTP) is not compatible with IEEE 802.1Q tunneling because you must 
manually configure asymmetric links with tunnel ports and trunk ports.

•

VLAN Trunking Protocol (VTP) does not work between devices that are connected by an 
asymmetrical link or devices that communicate through a tunnel.

•

Loopback detection is supported on IEEE 802.1Q tunnel ports. 

•

When a port is configured as an IEEE 802.1Q tunnel port, spanning-tree bridge protocol data unit 
(BPDU) filtering is automatically enabled on the interface. Cisco Discovery Protocol (CDP) and the 
Layer Link Discovery Protocol (LLDP) are automatically disabled on the interface.

Configuring an IEEE 802.1Q Tunneling Port

Beginning in privileged EXEC mode, follow these steps to configure a port as an IEEE 802.1Q tunnel 
port:

Command

Purpose

Step 1

configure terminal

Enter global configuration mode.

Step 2

interface 

interface-id

Enter interface configuration mode for the interface to be configured as a 
tunnel port. This should be the edge port in the service-provider network 
that connects to the customer switch. Valid interfaces include physical 
interfaces and port-channel logical interfaces (port channels 1 to 64).

Step 3

switchport access vlan

 

vlan-id

Specify the default VLAN, which is used if the interface stops trunking. 
This VLAN ID is specific to the particular customer. 

Step 4

switchport mode dot1q-tunnel

Set the interface as an IEEE 802.1Q tunnel port.

Содержание Catalyst 3130











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 3130

Lanner electronics FW-7650 Series User Manual preview
FW-7650 Series
Бренд: Lanner electronics Страницы: 57
D-Link DFL-300 - Security Appliance User Manual preview
DFL-300 - Security Appliance
Бренд: D-Link Страницы: 179
Watchguard XTM 2050 Quick Start Manual preview
XTM 2050
Бренд: Watchguard Страницы: 22
Lancom R&S Unified AGPO150 Migration Manual preview
R&S Unified AGPO150
Бренд: Lancom Страницы: 17
Fujitsu MB91401 Datasheet preview
MB91401
Бренд: Fujitsu Страницы: 72
ZyXEL Communications USG Series Quick Start Manual preview
USG Series
Бренд: ZyXEL Communications Страницы: 2
ZyXEL Communications Unified Security Gateway ZyWALL 300 Brochure & Specs preview
Unified Security Gateway ZyWALL 300
Бренд: ZyXEL Communications Страницы: 6
Draytek Vigor2952 Series Quick Start Manual preview
Vigor2952 Series
Бренд: Draytek Страницы: 15
Draytek GXP-1100 Technical Specifications preview
GXP-1100
Бренд: Draytek Страницы: 7
NETASQ NG1000-A Product Presentation And Installation preview
NG1000-A
Бренд: NETASQ Страницы: 63
FNGi DHCPatriot Quick Start Manual preview
DHCPatriot
Бренд: FNGi Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды