Repair
King Edge Vac
7-64
Loosen the air foil pivot bolt (Figure 7-92,
B). Be careful just to loosen the bolt, not
remove it completely.
Loosen the air foil positioning bolt and
washer. Be careful just to loosen the bolt,
not remove it completely.
Move the air foil slightly up or down as
deemed necessary. Normal positioning
is about 1” (25 mm) above the discharge
ribbons.
Tighten the air foil positioning and pivot
bolts.
Start the machine and run several pieces
to test the adjustment.
4.
5.
6.
7.
8.
Air Laydown Assist Air Pressure
Adjustment
The discharge conveyor air assist is designed
to improve the laydown of the flatwork as it leaves
the feeder and enters the ironer.
If the air assist pressure is set too high, it
might disturb the flatwork, causing ripples,
misalignment or other laydown problems. If it
is set too low, it may not provide the desired
improvement.
Note that the normal factory setting 30 psi
(205 kPa).
Perform only when the unit is
RUNNING.
Use extreme caution.
WARNING
This procedure will require
that you work while the
machine is running.
Use extreme caution.
Turn power ON at the main disconnect
switch.
Turn ON the compressed air supply to the
machine.
Feed several pieces and closely observe
the effect of vacuum assist on laydown
quality.
If the flatwork shows ripples or is oth-
erwise disturbed, the air pressure is too
high and should be lowered.
If the flatwork remains bumpy or is
not otherwise a little smoother, the air
pressure should be raised.
With the machine still running, carefully
duck under the front access guard. Be
extremely
careful of moving parts and
machinery.
1.
2.
3.
•
•
4.
TOC
INDEX
Содержание King Edge VAc
