Chattanooga SENIOR SOLUTIONS Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 108

background image

52

Senior Solutions™ Therapy System

6 REMOVAL/REPLACEMENT

6.2. MODULE INSTALLATION AND REMOVAL

A. Tools & Equipment Required

#1 Phillips Screwdriver
Flat Blade Screwdriver
Needle Nose Pliers

The following procedures apply to all Channel 3/4
Electrotherapy and NiMH Battery that mount to the
base of a Therapy System.

B. Module Installation

Disconnect Therapy System from the
power source.
Remove the Rear Panel and disconnect the
Power Cord from the System.

See Figure

6.1.

Place System on a level working surface.
Remove the Front Access Panel and
disconnect all existing cables and Lead
Wires.

See Figure 6.2.

Using a #1 Phillips Screwdriver, remove the
screw securing the Lanyard to the Front
Access Panel.

See Figure 6.3.

Turn system over, remove the label
covering the Ribbon Cable, and unroll
Ribbon Cable.

See Figure 6.4.

NOTE:

When turning over Therapy System onto
its face, place a clean, soft cloth under the
lens to prevent scratching or lens damage.
If the system is equipped with an sEMG
Module, leave it in place to maintain sEMG
functions for Channels 1 and 2. The sEMG
Module will not interfere with installation of
a Module to the Therapy System.

1.
2.
3.

1.

2.

3.
4.

5.

6.

FIGURE 6.1

FIGURE 6.2

REMOVE FRONT ACCESS

PANEL AND DISCONNECT

ALL CABLES

FIGURE 6.3

REAR PANEL

DISCONNECT

POWER CORD

REMOVE

LANYARD

FIGURE 6.4

REMOVE

LABEL

Be careful to not disconnect the Ribbon Cable from
the Senior Solutions Therapy System.

RIBBON

CABLE

LEAVE SEMG

IN PLACE

6.1 CHANNEL 3/4 ELECTROTHERAPY AND

NIMH BATTERY INSTALLATION AND

REMOVAL.

DISCONNECT THE SYSTEM FROM THE POWER
SOURCE (OUTLET OR REMOVE BATTERY MODULE IF
INSTALLED) BEFORE ATTEMPTING ANY MAINTENANCE,
INSTALLATION, REMOVAL, OR REPLACEMENT
PROCEDURES TO PREVENT ELECTRICAL SHOCK AND
POSSIBLE DAMAGE TO SYSTEM.

«
...
55
56
57
58
59
...
»

Содержание SENIOR SOLUTIONS













































































































Отзывы:

Нет отзывов

Похожие инструкции для SENIOR SOLUTIONS

Infield Rascal Pro

Бренд: ABI Attachments Страницы: 8

Бренд: Abicor Binzel Страницы: 84

Бренд: ABI Attachments Страницы: 5

Бренд: abem Страницы: 47

Бренд: Abely Страницы: 5

Бренд: Abicor Binzel Страницы: 92

Бренд: Raven Страницы: 12

Бренд: Zero 88 Страницы: 20

Бренд: Kapriol Страницы: 32

Бренд: Cabletron Systems Страницы: 33

Бренд: i-CAT Страницы: 32

Бренд: E-Z DRILL Страницы: 12

Бренд: e-survey Страницы: 54

Бренд: E-Pill Страницы: 8

XL-7 Command Station

Бренд: E-Mu Страницы: 22

Бренд: Eaton Страницы: 16

Бренд: Eaton Страницы: 6

Бренд: Ecco Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды