Chattanooga SENIOR SOLUTIONS Скачать руководство пользователя страница 72

Страница: 72 / 108

Senior Solutions™ Therapy System

6 REMOVAL/REPLACEMENT

6.11 THERAPY SYSTEM POWER SUPPLIES

NOTE:

The Senior Solutions Therapy System incorporates
two different Power Supply configurations:

Combination Therapy System-

Two Power

Supplies, one 75 Watt for Ultrasound Power and
one 100 Watt to power the rest of the system.

Electrotherapy System-

One 100 Watt Power

Supply.

A. Tools and Equipment Required

#1 Phillips Screwdriver
Insulated Needle Nose Pliers
Flat Blade Screwdriver
Digital Multimeter

B. Power Supply Removal

Separate Top from Bottom.

Refer to 6.4,

part B.

Remove Connector Board.

Refer to 6.8

part B.

Remove Ultrasound Board on Combination
Systems.

Refer to 6.9, part B.

Remove Stim Board.

Refer to 6.10, part B.

Using the # 1 Phillips Screwdriver, remove
the two screws securing the Power Supply
Assembly to the System Housing.

See

Figure 6.39.

Lift Power Supply Assembly up to remove
from rear mounting tabs.

See Figure 6.40.

Using the Digital Multimeter, discharge the
Power Supplies as follows:

100 Watt Power Supply- Discharge

Capacitor

C4.

See Figure 6.41.

75 Watt Power Supply (Combo Systems

  Only)- Discharge Capacitor on back of
  Power Supply PC Board. Pins are on
  either side of “R8A” on PC Board.

See

Figure

6.41.

1.
2.
3.
4.

4.
5.

REMOVE

SCREWS

REAR

MOUNTING

TABS

POWER SUPPLY

ASSEMBLY

BRACKETS

100 WATT

POWER SUPPLY

75 WATT

POWER SUPPLY

COMBINATION SYSTEMS ONLY

FIGURE 6.39

FIGURE 6.40

FIGURE 6.41

DISCONNECT THE SYSTEM FROM THE POWER
SOURCE (OUTLET OR REMOVE BATTERY MODULE IF
INSTALLED) BEFORE ATTEMPTING ANY MAINTENANCE,
INSTALLATION, REMOVAL, OR REPLACEMENT
PROCEDURES TO PREVENT ELECTRICAL SHOCK AND
POSSIBLE DAMAGE TO SYSTEM.

POWER SUPPLIES RETAIN HIGH VOLTAGE!
WHEN REMOVING FROM SYSTEM, HANDLE

POWER SUPPLIES BY MOUNTING BRACKETS
ONLY.

Содержание SENIOR SOLUTIONS













































































































Результаты поиска

Содержание SENIOR SOLUTIONS

Отзывы:

Похожие инструкции для SENIOR SOLUTIONS

Бренды по названию

Популярные бренды

Chattanooga SENIOR SOLUTIONS, Руководство по обслуживанию

Результаты поиска

Содержание SENIOR SOLUTIONS

Отзывы:

Похожие инструкции для SENIOR SOLUTIONS

Бренды по названию

Популярные бренды