Chattanooga SENIOR SOLUTIONS Скачать руководство пользователя страница 15

Страница: 15 / 108

Senior Solutions™ Therapy System

3 NOMENCLATURE

The nomenclature graphics below,

Figure 3.4

indicate the general locations of the exterior
components of the Senior Solutions Therapy
System Channel 3/4 Electrotherapy Module.
Know the components and their functions

before performing any operation of or service
to the Senior Solutions Therapy System Channel
3/4 Electrotherapy Module.

Two (2) Channel Electrotherapy Module

Extended Front Access Panel

Module to System Mounting Holes

Module to System Feet Alignment Indents

Power Cord Routing Port

Module to System Connector

Operator Remote Control Connector

Patient Interrupt Switch Connector

Channel 3 Lead Wire Connector

10.

Channel 4 Lead Wire Connector

11.

Microcurrent Probe Connector

Also Included:

Four 4 mm X 20 mm mounting screws

Channel 3 and 4 Lead Wires

Sample of Dura-Stick™ II Electrodes

NOTE:

The Channel 3/4 Electrotherapy Module is not
operable unless it is properly connected to a Senior
Solutions Therapy System.

•

3.1 SENIOR SOLUTIONS THERAPY SYSTEM (CONTINUED)

D. Senior Solutions Therapy System
Channel 3/4 Electrotherapy Module

FIGURE 3.4

Содержание SENIOR SOLUTIONS













































































































Результаты поиска

Содержание SENIOR SOLUTIONS

Отзывы:

Похожие инструкции для SENIOR SOLUTIONS

Бренды по названию

Популярные бренды

Chattanooga SENIOR SOLUTIONS, Руководство по обслуживанию

Результаты поиска

Содержание SENIOR SOLUTIONS

Отзывы:

Похожие инструкции для SENIOR SOLUTIONS

Бренды по названию

Популярные бренды