manualshive.com logo in svg

Chattanooga SENIOR SOLUTIONS, Руководство по обслуживанию, Страница: 64 / 108

Поделиться
Скачать
Chattanooga SENIOR SOLUTIONS Скачать руководство пользователя страница 64

59

 Senior Solutions™ Therapy System

6 REMOVAL/REPLACEMENT

6.4 THERAPY SYSTEM SEPARATING 
 TOP 

& 

BOTTOM

A. Tools and Equipment Required

#1 Phillips Screwdriver
Flat Blade Screwdriver

B. Separating Top from Bottom

Place system face down on a soft work 
surface.
Remove any Module (NiMH Battery, Channel 
3/4 Electrotherapy) from the System. 

Refer 

to 6.2 Module Installation and Removal

 

for instructions.

NOTE:

It is not necessary to remove an sEMG 
Module from the System unless the Stim 
Board is being replaced.
Remove the four mounting screws 
securing the top and bottom. 

See Figure 6.18.

Turn System over on its feet and carefully 
separate the System Top from the Bottom 
Housing.

NOTE:

On Combination Systems, it may be 
necessary to use a Flat Blade Screwdriver 
around the Ultrasound Applicator Rest to 
separate the top from the bottom. 

See 

Figure 6.19.

Raise the System Top and disconnect the 
Control Board Ribbon Cable from the Stim 
Board or Ultrasound Board on Combination 
Systems.

 See Figure 6.20.

1.
2.

1.

2.

3.

4.

5.

FIGURE 6.18

FIGURE 6.19

FIGURE 6.20

REMOVE 4 SCREWS

CONTROL BOARD 

RIBBON CABLE

DISCONNECT THE SYSTEM FROM THE POWER 
SOURCE (OUTLET OR REMOVE BATTERY MODULE IF 
INSTALLED) BEFORE ATTEMPTING ANY MAINTENANCE, 
INSTALLATION, REMOVAL, OR REPLACEMENT 
PROCEDURES TO PREVENT ELECTRICAL SHOCK AND 
POSSIBLE DAMAGE TO SYSTEM.

Содержание SENIOR SOLUTIONS













































































































Отзывы:

Нет отзывов