background image

62

 Senior Solutions™ Therapy System

6 REMOVAL/REPLACEMENT

6.6 THERAPY SYSTEM 
 CONTROL 

BOARD 

ASSEMBLY

 

A. Tools and Equipment Required

#1 Phillips Screwdriver
Needle Nose Pliers

 

B. Control Board Assembly Removal

Separate Top from Bottom. 

Refer to 6.4, 

part B.

Remove Fan. 

Refer to 6.5, part B.

Remove the Contrast Knob.

 See Figure 6.25.

Remove the Control Board Ribbon Cable and 
the two Control Board Assembly Retaining 
Screws. 

See Figure 6.26.

STARTing at the top of the Control Board 
Assembly, lift Control Board with one hand, 
push in and release the plastic clips holding 
Control Board Assembly in position. 

See 

Figure 6.27.

While holding up on Control Board Assembly, 
use the Needle Nose Pliers to squeeze the 
lower plastic retainers holding the bottom of 
the Control Board. 

See Figure 6.27

 inset.

Remove the Card Reader Housing from the 
Control Board Assembly.

 

C. Replacing Control Board Assembly

Replace new Control Board Assembly, part 
number 27053, by reversing the 

steps 1- 7 

above.

NOTE:

Do not over tighten the screws. Over 
tightening will damage the threads of the 
brass inserts.
Install Therapy Intensity Control Knob on the 
front side of Therapy System Top.
Re-assemble Therapy System referring to the 
appropriate sections of this manual for proper 
instructions.

1.
2.

1.

2.
3.
4.

5.

6.

7.

1.

2.

3.

FIGURE 6.25

FIGURE 6.26

CONTRAST KNOB

REMOVE

RETAINING

SCREWS

FIGURE 6.27

REMOVE

RIBBON CABLE

DISCONNECT THE SYSTEM FROM THE POWER 
SOURCE (OUTLET OR REMOVE BATTERY MODULE IF 
INSTALLED) BEFORE ATTEMPTING ANY MAINTENANCE, 
INSTALLATION, REMOVAL, OR REPLACEMENT 
PROCEDURES TO PREVENT ELECTRICAL SHOCK AND 
POSSIBLE DAMAGE TO SYSTEM.

MAKE CERTAIN THE CONTROL BOARD RIBBON 
CABLE IS INSTALLED WITH THE BLACK STRIP AT THE 
NUMBER “1” ON THE CONTROL BOARD. FAILURE 
TO PROPERLY INSTALL RIBBON CABLE COULD 
CAUSE EXTENSIVE DAMAGE TO THE INTERNAL 
COMPONENTS OF THE SYSTEM WHEN TURNED ON.

Содержание SENIOR SOLUTIONS













































































































Отзывы: