manualshive.com logo in svg

Chattanooga SENIOR SOLUTIONS, Руководство по обслуживанию, Страница: 77 / 108

Поделиться
Скачать
Chattanooga SENIOR SOLUTIONS Скачать руководство пользователя страница 77

72

 Senior Solutions™ Therapy System

7 GENERAL MAINTENANCE

7.1 CLEANING THE SYSTEM

 

A. Cleaning the Therapy System

With the system disconnected from the power 
source, clean the system with a clean, lint 
free cloth moistened with water and mild 
antibacterial soap. If a more sterile cleaning 
is needed, use a cloth moistened with an 
antimicrobial cleaner.
Do not submerse the system in liquids. Should 
the unit accidentally become submersed, 
contact the dealer or Chattanooga Group 
Service Department immediately. Do not 
attempt to use a system that has been wet 
inside until inspected and tested by a Service 
Technician certified by Chattanooga Group.
Do not allow liquids to enter the ventilation holes 
in the optional modules. This could permanently 
damage the modules.

 

B. Lens Cleaning

 

Therapy System Screen Lens

Clean the Therapy System Lens with the 
NOVUS® Plastic Polishing System. NOVUS can 
be purchased by going to novuspolish.com on 
the internet. Follow the instructions as given by 
NOVUS on their product.
Do not use alcohol or chlorine-based solvents 
as this may damage the lens.

7.2 CALIBRATION REQUIREMENTS

 Ultrasound 

Applicators:

Annual factory calibration is required for all 
Ultrasound Applicators. Only the Applicators 
should be sent to the factory for this 
procedure.

7.3 FIELD SERVICE

A.

 All field service procedures as described in 

this Service Manual for the Senior Solutions 
Therapy System must be performed by a 
Service Technician certified by Chattanooga 
Group.

 

B.

 Any work attempted outside the scope of this 

Service Manual is the sole responsibility and 
liability of the Field Technician performing such 
procedures.

7.4 FACTORY SERVICE

When the Senior Solutions Therapy System 
requires factory service, contact the dealer or 
Chattanooga Group Service Department.

       

NOVUS is the Registered Trademark of NOVUS Inc.

DISCONNECT THE SYSTEM FROM THE POWER 
SOURCE (OUTLET OR REMOVE BATTERY MODULE IF 
INSTALLED) BEFORE ATTEMPTING ANY MAINTENANCE, 
INSTALLATION, REMOVAL, OR REPLACEMENT 
PROCEDURES TO PREVENT ELECTRICAL SHOCK AND 
POSSIBLE DAMAGE TO SYSTEM.

Содержание SENIOR SOLUTIONS













































































































Отзывы:

Нет отзывов