background image

51

 Senior Solutions™ Therapy System

5 TROUBLESHOOTING

Using the Flat Blade Screwdriver, carefully 
release the tabs retaining the top plate in 
position. It will be necessary to lift with 
one hand while releasing the tabs  with 
the Screwdriver. 

See Figure 5.38.

NOTE:

There are eight retaining tabs. All must be 
released as shown in 

Figure 5.38.

Lift the PC Board and check the Battery 
Packs to PC Board connection to ensure it 
is completely seated. 

See Figure 5.39.

Visually inspect individual cells of both 
battery packs for leaks or ruptures. 

See 

Figure 5.40.

Reassemble the battery Module. Do not 
over tighten the two retaining screws in 
the module top. Over-tightening may 
damage the threaded brass inserts of the 
housing.

C. NiMH Battery Module Checks Results

Should any check fail, replace the entire 
module. No component parts are or will be 
made available for the Battery Module by 
Chattanooga Group.
If the problem persists, replace the Control 
Board.

10.

11.

12.

13.

1.

2.

FIGURE 5.40

FIGURE 5.39

FIGURE 5.38

NiMH batteries contain Class E corrosive 
materials. In the event of battery cell rupture 
or leakage, handle battery module wearing 
neoprene or natural rubber gloves. Contents 
of a ruptured or leaking battery can cause 
respiratory irritation. Hypersensitivity to 
nickel can cause allergic pulmonary asthma. 
Contents of cell coming in contact with skin 
can cause skin irritation and chemical burns.

Never, under any circumstances, open the 
battery cells. Should an individual cell from a 
battery become disassembled, spontaneous 
combustion of the negative electrode is 
possible. There can be a delay between 
exposure to air and spontaneous combustion.

Содержание SENIOR SOLUTIONS













































































































Отзывы: