Challenge Titan 265 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 88

background image

8.0 Maintenance Guide

49

6. Turn the side gib screws in until they just touch the guide. The backgauge should not be able

to rock side to side. Lock in position with the jam nuts.

7. Run the backgauge back and forth the length of the table using the backgauge glide control.

Check for any binding. Readjust if necessary.

NOTE:

The screws should be tightened to hold the backgauge square against the guide rail.

Excessive tightening will cause the backgauge to bind and cause premature wear of all components.

8.7.2 Squaring the Backgauge

Figure 28

To test the backgauge for squareness, place a small lift of paper against the left side of the
backgauge (but not against the side guide) and make a cut.

Now, leave the backgauge in the same position, flip the lift over and against the right side of the
backgauge (but not against the side guide). Make another cut to see if any of the stock will trim off.
Run two checks, one starting on the left and moving to the right, the other, moving from the right to
the left. Trim in either sequence indicates the backgauge is out of square.

1. Make sure the backgauge gibs are set properly, (see the Backgauge Gib Adjustments section

on page 48). Then follow steps 2 through 5.

NOTE

: Gib adjustment is not necessary on initial machine setup as gibs have been adjusted at the

factory.

2. Loosen backgauge locking screw (smaller head). Loosen the jam nuts on the backgauge

adjusting screws (

3. Figure 29).

Figure 29

PAPER

PAPER

Adjusting Screws with Jam Nuts

Shoulder

Screw

Locking

Screw

«
...
48
49
50
51
52
...
»

Содержание Titan 265

























































































Отзывы:

Нет отзывов

Похожие инструкции для Titan 265

Бренд: Reliable Страницы: 1

Бренд: Maktec Страницы: 8

Бренд: Garland Страницы: 84

Бренд: BIMG Страницы: 20

Бренд: QEP Страницы: 8

VANGUARD OPTIMA

Бренд: Hermes Страницы: 113

Бренд: Dremel Страницы: 64

Бренд: 2M2 Страницы: 24

Бренд: Sandr Garden Страницы: 77

Бренд: Hypertherm Страницы: 98

Бренд: Hypertherm Страницы: 94

Бренд: CountyLine Страницы: 40

Бренд: Proxxon Страницы: 28

Бренд: Tanaka Страницы: 18

Бренд: Zenoah Страницы: 27

Бренд: Zenoah Страницы: 16

Бренд: Zenoah Страницы: 16

Бренд: Xyron Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды