Challenge Titan 265 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 88

background image

8.0 Maintenance Guide

48

8.6 Oil and Grease

Turn the power off and disconnect the power cord. Open the front guard (if equipped) and open the
top hood for access. Parts requiring oiling are marked with red paint. See Figure 24, Figure 25, and
Figure 26

on page 47, for oil and grease locations. Wipe off any old or excess grease. Use any

brand-name type of grease or light oil to lubricate. It may be necessary to use the supplied grease
brush to access some locations. Note: the leadscrew may be lubricated with grease or oil. Oil has a
tendency to run off and must be lubricated more frequently; grease tends to collect paper dust and
must be cleaned off periodically.

8.7 Adjustments

Several of the following tests require the machine to be operational

for checking and adjusting. Be very careful that tools and other people are clear of moving
parts and that the cutter is not accidentally operated while adjustments are being made.
Whenever working on the machine, disconnect the power and lock it out (see SAFETY
PRECAUTIONS, page 6) unless the directions specifically require the machine to be powered.

8.7.1 Backgauge Gib Adjustments

If the backgauge does not stay squared or jumps up and down when jogging paper against it, the
backgauge gib screws are probably loose or worn.

To Adjust:

1. Send the backgauge near the rear of the table.

2. Turn off the power and lock it out, page 6.

3. Remove the leadscrew cover under the table.

4. Loosen the side gib setscrews and the bottom nylon guide screws (Figure 27).

Figure 27

5. Tighten the bottom nylon guide screws until they touch the guide then back off 1/8 turn. Do

not over-tighten or they could cause the backgauge to bind.

Gib Screws

Nylon Guide

Screws

«
...
47
48
49
50
51
...
»

Содержание Titan 265

























































































Отзывы:

Нет отзывов

Похожие инструкции для Titan 265

Бренд: Land Pride Страницы: 30

Бренд: Garland Страницы: 144

Бренд: Olfa Страницы: 1

Evolution3 BenchTop

Бренд: KEENCUT Страницы: 4

Бренд: Webb Страницы: 36

Бренд: Gardena Страницы: 11

Бренд: Custom Crimp Страницы: 25

Бренд: RASOR Страницы: 15

Бренд: Rittal Страницы: 52

Бренд: pellenc Страницы: 42

Бренд: Raider Страницы: 30

Бренд: Raider Страницы: 33

Бренд: Raider Страницы: 33

FoamWerks WA-8001

Бренд: Logan Graphic Products Страницы: 2

Бренд: Hengstler Страницы: 4

Бренд: Taewoo Страницы: 14

Бренд: Olympia Tools Страницы: 2

Бренд: BN Products Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды