Challenge Titan 265 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 88

background image

7.0 Knife Installation/Changing

38

10. Plug in the power cord and turn the power on.

11. Go to the MAINTENANCE screen and choose KNIFE ADJUST. Choose KNIFE DOWN,

close the guard, and press the cut button to send the knife to the down position (for more
details on how to do this, see page 26, Knife Adjustment).

12. Turn the power off and disconnect the machine power cord.

13. Turn the knife adjusters down evenly, a little at a time, until the knife cuts through the bottom

sheet of paper the entire length of the cutting stick (Figure 22). Turning the screws down
evenly prevents uneven wear on the knife and cutting stick.

Figure 22

14. Plug in the power cord and turn the power on.

15. Close the front guard and press CLEAR. This will raise the knife and clamp to the up

position.

16. Turn the power off and disconnect the machine power cord.

17. Tighten all knife bolts securely.

18. Plug in the power cord and turn the power on. Make a test cut through a full lift of paper and

make minor adjustments if necessary by repeating steps 9 through 17.

NOTE:

If the knife

ends cut but the middle doesn’t, you could have dips or uneven spots in the knife and/or
cutting stick. These can be eliminated by placing 1/2” strips of paper in the table slot beneath
the cutting stick to shim it.

19. Send the dull knife to a knife grinder. Do not attempt to sharpen your own knives! See the

Knife Care Tips Section below to determine the knife bevel angle.

7.3 Knife Care Tips

! KNIFE SAFETY

! Knives are

DANGEROUS!!!

They are heavy and very

sharp, even after use. Keep the edge away from your body and keep the area clear of others when
handling knives. Never touch the cutting edge! To prevent personal injury and damage to the knife,
always keep knives in their holders with screws tightened. You are aware of the dangers, but others
may not be. Never attempt to hone, polish, or service the knife in any way. Failure to follow safety
procedures may result in severe lacerations or dismemberment.

«
...
37
38
39
40
41
...
»

Содержание Titan 265

























































































Отзывы:

Нет отзывов

Похожие инструкции для Titan 265

Бренд: LawnBoss Страницы: 20

eclips EC-C1200

Бренд: Ellison Страницы: 36

Бренд: Gardol Страницы: 124

Бренд: Vollrath Страницы: 12

Бренд: Martin Yale Industries Страницы: 4

PULVERISETTE 19

Бренд: Fritsch Страницы: 62

Бренд: RedMax Страницы: 40

Бренд: RASOR Страницы: 16

GocMakSan MG20B 220V DIGITAL

Бренд: GMS Страницы: 9

Бренд: Rexel Страницы: 30

Бренд: Value Leader Страницы: 34

Бренд: RASOR Страницы: 15

Omk.SZP01.E11.0101.Z5F

Бренд: omake Страницы: 49

Бренд: EMAK Страницы: 166

Бренд: EMAK Страницы: 300

Бренд: Makita Страницы: 44

Бренд: Toyama Страницы: 56

Бренд: Husqvarna Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды