Carbide 3D Shapeoko XXL Скачать руководство пользователя страница 55

Страница: 55 / 110

from the bottom in the gap nearest the end of
the clip as shown in Step 1.

2. The belt is next inserted into from the top to

the bottom in the second gap as shown in Step
2.

3. Pull the belt so that 2” returns in the direction

of the top portion of the belt. Make certain the
teeth of the top and lower sections of belt are
interlocked as shown in Step 3.

NOTE:

The free end of the belt (the end not

looped through a belt clip) will be routed
through the carriages and then secured using
another belt clip using more detailed steps
provided below.

X-Axis Rail Belt

Installation

Insert one end of a belt through the belt clip as
described above. Ensure that the bottom 2” portion
of belt interlocks with the top portion and secure it
to the Y-Axis Left Carriage as shown in the image
below.

Содержание Shapeoko XXL







































































































Результаты поиска

Содержание Shapeoko XXL

Отзывы:

Похожие инструкции для Shapeoko XXL

Бренды по названию

Популярные бренды

Carbide 3D Shapeoko XXL, Руководство пользователя

Результаты поиска

Содержание Shapeoko XXL

Отзывы:

Похожие инструкции для Shapeoko XXL

Бренды по названию

Популярные бренды