Carbide 3D Shapeoko XXL Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 110

background image

NOTE:

It is recommended you not stress this

tape for at least three minutes after the initial
application.

Secure X-Axis Drag Chain

Using the remaining alcohol wipe, clean the X-Axis
Rail approximately three (3) inches from the Left Y-
Axis Carriage.

Using the same method to secure the Y-Axis Drag
Chain, clean the X-Axis Rail with the alcohol wipe,
allowing to dry if alcohol is still present. Apply the
VHB tape, keeping the upper side of the protective
film on, and pressing down firmly and completely
for at least 30 seconds.

Remove the protective film from the upper side of
the tape. Center the free end of the X-Axis Drag
Chain over the VHB tape and press down firmly for
a minimum of 30 seconds.

«
...
91
92
93
94
95
...
»

Содержание Shapeoko XXL















































































































Отзывы:

Нет отзывов

Похожие инструкции для Shapeoko XXL

Бренд: Lawler Страницы: 5

Бренд: Garmin Страницы: 12

Бренд: Gardena Страницы: 17

Бренд: SAFI Страницы: 18

Бренд: Badger Meter Страницы: 2

Бренд: Badger Meter Страницы: 48

BadgerTouch HREBT

Бренд: Badger Meter Страницы: 12

Бренд: Badger Meter Страницы: 16

Бренд: UNITED Страницы: 22

Бренд: IBM Страницы: 38

Compact Comfort VAV12

Бренд: SAI HVAC Страницы: 16

Бренд: saia-burgess Страницы: 203

Бренд: Sailor Страницы: 1

Бренд: Vaillant Страницы: 27

Бренд: Vaillant Страницы: 36

Бренд: Vaillant Страницы: 28

Бренд: Vaillant Страницы: 92

Бренд: ValvTechnologies Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды