Carbide 3D Shapeoko XXL Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 110

background image

The Y-Axis Left Carriage will be bolted to the X-Axis
Extrusion Rail using four (4x) of the M6x12mm
screws.

The bearings on the Y-Axis Left Carriage will ride on
the V-rail of the left Extrusion Rail; this means the
Y-Axis Left Carriage must be bolted to the X-Axis
Extrusion Rail with the bearings facing outward (or
to the left) and the motor pointing in (or to the
right) as shown in the photo below.

Before bolting on the Y-Axis Left Carriage to the X-
Axis Extrusion Rail, place the empty carriage boxes
underneath the X-Axis Extrusion Rail to hold it up
and allow for easier attachment of the Y-Axis Left
Carriage as shown in the image below.

«
...
39
40
41
42
43
...
»

Содержание Shapeoko XXL















































































































Отзывы:

Нет отзывов

Похожие инструкции для Shapeoko XXL

Бренд: Danfoss Страницы: 32

PVG 16 PVH/Covers

Бренд: Danfoss Страницы: 112

Бренд: Danfoss Страницы: 44

PVG 16 PVH/Covers

Бренд: Danfoss Страницы: 144

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 64

Бренд: Danfoss Страницы: 8

VLT AutomationDrive FC 360

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 6

Бренд: Danfoss Страницы: 4

Бренд: Danfoss Страницы: 8

Бренд: Danfoss Страницы: 2

ECL Comfort 110

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 24

Бренд: Danfoss Страницы: 37

Бренд: Daikin Страницы: 44

Бренд: Salda Страницы: 16

Бренд: Feig Electronic Страницы: 153

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды