Carbide 3D Shapeoko XXL Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 110

background image

The Shapeoko XXL ships with three (3x) limit
switches. One for the X axis, one for the Y axis, and
one for the Z axis. Each limit switch is attached to a
twisted-wire pair of black and yellow wires.

The switches are pre-installed to their respective
plates during the harness assembly in the factory.
In this step we will connect those plates to their
permanent locations on the machine.

Z-Axis Limit Switch

Attach the Z-Axis Limit Switch by locating the larger
plate from the end of the harness and connecting
to the front of the X/Z assembly. This plate is visible
in the image below.

You may need to adjust your wiring from the
harness at this point. The wiring is zip-tied
together, but is not bound to the drag chains.
Gently pulling on the wires for more length is
acceptable.

NOTE:

If the wires you are attempting to pull

do not slide freely, make sure they are not
snagged at the other end of the drag chain.

«
...
76
77
78
79
80
...
»

Содержание Shapeoko XXL















































































































Отзывы:

Нет отзывов

Похожие инструкции для Shapeoko XXL

Бренд: Campbell Страницы: 3

Бренд: eclisse Страницы: 40

Бренд: Samson Страницы: 52

Бренд: Garmin Страницы: 4

Бренд: HALDER Страницы: 2

coviva Smartbox TKP100A

Бренд: hager Страницы: 4

Бренд: Vag Страницы: 12

Бренд: Harmonic Drive Страницы: 85

Бренд: Jedia Страницы: 12

Бренд: JED Micro Страницы: 10

Бренд: JCM Technologies Страницы: 2

Бренд: Balboa Страницы: 23

Бренд: Balboa Страницы: 2

Бренд: Saluki Страницы: 13

Бренд: Gardena Страницы: 236

Бренд: Aeta Audio Systems Страницы: 24

Бренд: Reer Страницы: 2

Бренд: M-system Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды