manualshive.com logo in svg

Car-O-Liner BenchRack 4200, Инструкция по эксплуатации

Поделиться
Скачать
Car-O-Liner BenchRack 4200 Скачать руководство пользователя страница 6

 
 

 
 

Car-O-Liner Group AB 

BenchRack 

6

 

32163, EN- rev. 5,

 

2018-04

 

1 Introduction 

1.1 General 

BenchRack is used for vehicle alignment and has an integrated, variably 
adjusted scissors lift which can raise the bench frame to the maximum 
working height of 1170 mm. 

The bench frame has drive-on ramps and ramp sections, so-called “side 
ramps”.The side ramps are easily hooked to the side tracks of the bench 
frame. 

The ramps permit a vehicle to be driven on to the bench frame for quick an-
choring of chassis clamps (such as Standard Clamp B106). 

The bench frame may be tilted to facilitate driving on the vehicle. 

Maximum permitted vehicle weight is 4200 kg. 

Maximum load per ramp section is 1000 kg. 

 

IMPORTANT!

 The complete vehicle shall be positioned on the bench 

when carrying out alignment work. The lift and bench frame shall not be 
used to lift one end of the vehicle while the other end remains on the floor. 
Moreover, the lift’s working platform shall not be used for anything other 
than vehicle repair. 

Содержание BenchRack 4200
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды