Car-O-Liner BenchRack 4200 Скачать руководство пользователя страница 10

Страница: 10 / 55

Car-O-Liner Group AB

BenchRack

32163, EN- rev. 5,

2018-04

WARNING!

All work on the electrical equipment must be carried out by

qualified personnel.

WARNING!

Maximum vehicle weight = 4200 kg. Minimum allowed

distance between axles is 2500 mm..

WARNING!

During all service and fitting work, the lift must be blocked

up while in the raised position to prevent accidental lowering. Risk of
crushing injuries.

WARNING!

The cable protection must be properly fastened over the air

and hydraulic hoses. Risk of tripping.

IMPORTANT!

If there is any uncertainty about the quality of the floor,

contact a building engineer for an inspection.

WARNING!

During set-up of the vehicle on the bench, care must be

exercised so that the vehicle does not roll or slide out of the supports or
mountings. Risk of crushing injuries.

IMPORTANT!

Ensure that the toothed segments are clean and fitted

correctly.

WARNING!

When other personnel are in the vicinity exercise care when

operating the lift. Risk of crushing injuries.

WARNING!

Ensure that all of the bench legs hang straight down. Risk of

injury.

WARNING!

The control lever must be fully pushed in. Risk of injury.

WARNING!

Before raising or lowering the lift, ensure that no-one is near

the bench. Risk of crushing injuries.

WARNING!

Observe high standards of cleanliness when working with the

hydraulic system. Dirt in the hydraulic oil can cause operating problems.

WARNING!

Never lift the vehicle with two pillar jacks placed under the

vehicle´s center of gravity. Risk of instability and of crushing injuries.

Содержание BenchRack 4200
























































Результаты поиска

Содержание BenchRack 4200

Отзывы:

Бренды по названию

Популярные бренды

Car-O-Liner BenchRack 4200, Инструкция по эксплуатации

Результаты поиска

Содержание BenchRack 4200

Отзывы:

Бренды по названию

Популярные бренды