Car-O-Liner BenchRack 4200 Скачать руководство пользователя страница 46

Страница: 46 / 55

Car-O-Liner Group AB

BenchRack

32163, EN- rev. 5,

2018-04

6.4

Problem: The lift cannot be lowered

Fault

Possible cause

Solution

Lowering valve fails to open. See the separate
instruction manual for the Power unit.

1. No current to the magnetic coil.

Check the voltage on the coil (24 V AC).
Trouble shoot according to the diagram.

2. The valve is blocked with dirt.

Clean the valve.

3. The valve sticks.

Change the valve and the oil.

4. The latch pawl (4) is stiff or sticks.

Clean so that the pawl enters the slot
easily.

Mechanical safety latch (3) is jammed.

Air cylinder (7) does not lift the latch pawl
from the slot.

Check the air supply to the air valve, see
the separate instruction manual for the
Power unit, and that the air valve receives
24 V AC. Make sure that the air hose is
not crushed or blocked.

Jumper connector on electrical box not inserted. Plug in the jumper connector

Содержание BenchRack 4200
























































Результаты поиска

Содержание BenchRack 4200

Отзывы:

Бренды по названию

Популярные бренды

Car-O-Liner BenchRack 4200, Инструкция по эксплуатации

Результаты поиска

Содержание BenchRack 4200

Отзывы:

Бренды по названию

Популярные бренды