manualshive.com logo in svg

Car-O-Liner BenchRack 4200, Инструкция по эксплуатации

Поделиться
Скачать
Car-O-Liner BenchRack 4200 Скачать руководство пользователя страница 33

 
 

 
 

BenchRack Car-O-Liner 

Group 

AB 

32163, EN  - rev. 5,

 

2018-04 

33

 

 

3.

 

Mark the placement points A and B for the chassis clamps. The 
measurements are given in the DataSheet (see Measuring software). 
Remove underseal and dirt from the sill edge to give the chassis 
clamps a good grip and to ensure that the correct height is obtained 
when measuring (important when using Car-O-Mech). 

 

4.

 

Raise the lift to its highest position and fit two pillar jacks according 
to picture (right and left side of the vehicle). 
Remove ramps where the pillar jacks are to be positioned. 
Adjust the position of the pillar jacks for a suitable lifting point.  

 

 

WARNING!

 Never lift the vehicle with two pillar jacks placed under the 

center of gravity of the vehicle. Risk of instability and of crushing injuries. 

 

 

Pillar jack (x2) 

Содержание BenchRack 4200
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды