manualshive.com logo in svg

Car-O-Liner BenchRack 4200, Инструкция по эксплуатации

Поделиться
Скачать
Car-O-Liner BenchRack 4200 Скачать руководство пользователя страница 27

 
 

 
 

BenchRack Car-O-Liner 

Group 

AB 

32163, EN  - rev. 5,

 

2018-04 

27

 

 

Ensure that the draw aligner can be easily connected to all sides of the bench 
frame (see section on draw aligner). Adjust using the support screws if nec-
essary. 

Install the cable protection (optional) over the air and hydraulic hoses. 

WARNING!

 The cable protection must be properly fastened over the air 

and hydraulic hoses. Risk of tripping. 

 

Raise and lower the lift a few times to ensure that the safety latch element 

(Figure 3.2)

 falls easily into the slot. Lubricate if necessary. 

WARNING!

 Ensure that the crush guard is fitted so that it always drops 

down of its own weight and does not bind. Risk of crushing injuries. 

 

Position the warning decals and signs providing instructions for lift and 
alignment work

, section 2 "Safety". 

 

IMPORTANT!

 Before first vehicle setup, remove all grease from the milled 

surfaces of the bench tracks to prevent the bench mountings from slipping.  

 

Содержание BenchRack 4200
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды