manualshive.com logo in svg

Car-O-Liner BenchRack 4200, Инструкция по эксплуатации

Поделиться
Скачать
Car-O-Liner BenchRack 4200 Скачать руководство пользователя страница 18

 
 

 
 

Car-O-Liner Group AB 

BenchRack 

18

 

32163, EN- rev. 5,

 

2018-04

 

3.2.1 Drive-on 

ramps 

The drive-on ramps are attached to the brackets on the end of the bench and 
to the two side ramp brackets.  

The drive-on ramps may remain in place while the bench is raised or 
lowered, but can be removed if necessary. 

NOTE! 

The vehicle must be firmly attached to the bench frame! 

The drive-on ramps also act as drive-off stops when the lift is raised. 
The drive-on ramps are used with all tilt able BenchRacks. 

NOTE!

 A wider drive-on ramp is available for all BenchRack models! 

 

3.2.2 

Drive-on stops B44 

The drive-off stops should always be properly fitted (see illustration). The 
stops not only prevent a vehicle from rolling forward off of the BenchRack, 
but also prevent improper weight distribution on the bench and lift. 

1 

Applies to BR5500 and BR6300 

2

 

Applies to BR4200 and BR5000 

 

WARNING!

   The drive-off stops should always be correctly fitted to the 

bench. Risk of improper weight distribution. 

1 

2 

Содержание BenchRack 4200
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды