manualshive.com logo in svg

Car-O-Liner BenchRack 4200, Инструкция по эксплуатации

Поделиться
Скачать
Car-O-Liner BenchRack 4200 Скачать руководство пользователя страница 39

 
 

 
 

BenchRack Car-O-Liner 

Group 

AB 

32163, EN  - rev. 5,

 

2018-04 

39

 

 

5.

 

With the vehicle supported by the pillar jacks (left and right side), 
gently lower the lift to allow the front bench mountings and chassis 
clamps to be fitted. For correct placing of the bench mountings and 
chassis clamps, see section 4.2.1 Drive on to BenchRack.  

6.

 

Gently raise the the bench to fit the clamps to the sill flange. For 
correct fitting of the bench mountings and chassis clamps, see 
section 4.2.2 Setup with chassis clamps. 

NOTE

!  Do not tighten the bolts for the clamp plates to the bench 

mounting before all 4 chassis clamps are in position. 

NOTE!

 Tighten the chassis clamps; first against the sill edge and then 

against the bench mounting. 

 

7.

 

Repeat the procedure described in step 5. 

8.

 

Repeat the procedure described in step 6.  

NOTE

!  Do not tighten the bolts for the clamp plates to the bench 

mounting before all 4 chassis clamps are in position. 

NOTE

!  Tighten the chassis clamps; first against the sill edge and then 

against the bench mounting. 

 

 

Содержание BenchRack 4200
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды