manualshive.com logo in svg

Car-O-Liner BenchRack 4200, Инструкция по эксплуатации

Поделиться
Скачать
Car-O-Liner BenchRack 4200 Скачать руководство пользователя страница 26

 
 

 
 

Car-O-Liner Group AB 

BenchRack 

26

 

32163, EN- rev. 5,

 

2018-04

 

 

WARNING!

 All work on the electrical equipment must be carried out by 

qualified personnel. 

 

Make the electrical and hydraulic connections to the lift and drive unit. For 
electrical installation, see the separate instruction manual for the Power unit. 

WARNING!

 Maximum vehicle weight = 4200 kg. 

Minimum allowed distance between axles is 2500 mm. 

 

Raise the lift to the highest position and block up the bench frame. 

WARNING!

 During all service and fitting work, the lift must be blocked up 

while in the raised position to prevent accidental lowering. Risk of crushing 
injuries. 

 

Engage the two safety latches. 

Mark the 4-6 mounting holes on the floor and fit the floor brackets according 
to the, 

section 3.5.3 "Anchoring to the floor".

 

Raise the lift and remove the blocks from under the bench frame. 

WARNING!

 Before raising or lowering the lift, ensure that no one is near 

the bench. Risk of crushing injuries. 

 

Lower the lift to the draw aligner height. 

!

Содержание BenchRack 4200
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды