manualshive.com logo in svg

Car-O-Liner BenchRack 4200, Инструкция по эксплуатации

Поделиться
Скачать
Car-O-Liner BenchRack 4200 Скачать руководство пользователя страница 35

 
 

 
 

BenchRack Car-O-Liner 

Group 

AB 

32163, EN  - rev. 5,

 

2018-04 

35

 

 

4.4.2 

Setup with chassis clamps 

1.

 

With the vehicle supported by the pillar jacks (left and right side), 
gently lower the lift to give space for the front bench mountings and 
chassis clamps to be fitted. Remove side ramps from under the front 
wheels. 

  

2.

 

Place the front bench mountings and cam locks in the centre of the 
B mark (see section 4.2.1 "Drive on to BenchRack"). Tighten the 
bench mountings with the cam locks to the bench. Fit the chassis 
clamps to the bench mountings and check that they are placed 
directly under the sill edge. Gently raise the the bench to fit the 
clamps to the sill flange. Tighten the clamps to the sill flange. 

 

NOTE

!  Do not tighten the bolts for the clamp plates to the bench mounting 

before all 4 chassis clamps are in position. 

Bench mounting and 

chassis clamp 

Содержание BenchRack 4200
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды