manualshive.com logo in svg

Car-O-Liner BenchRack 4200, Инструкция по эксплуатации

Поделиться
Скачать
Car-O-Liner BenchRack 4200 Скачать руководство пользователя страница 2

 
 

 
 

Car-O-Liner Group AB 

BenchRack 

2

 

32163, EN- rev. 5,

 

2018-04

 

Foreword 

This equipment is used to facilitate high quality re-
pairs to collision-damaged vehicles. All other use of 
the equipment, or use that is contrary to the instruc-
tions in this manual, can cause personal injury and/or 
equipment damage. 

Car-O-Liner Group AB including any company within 
the Car-O-Liner Group of companies ("Car-O-Liner") 
can not

 

be held responsible for any claims for loss or 

damages as a result from incorrect use of this equip-
ment or its use in a manner not intended. Save for 
product liability claims for loss or damages as a result 
of personal injury or damage to property to the extent 
caused by the negligence, gross negligence, breach of 
contract, or other wrongdoing of Car-O-Liner (as 
prescribed by the Product Liability Act (1992:18) or 
similar legislation applicable on other markets), Car-
O-Liner shall in no event be liable for any loss or 
damage to revenues, profits or goodwill or other spe-
cial, incidental, indirect or consequential damages of 
any kind. 

Warranty 

Car-O-Liner offers a one-year limited guarantee from 
the date of installation of the equipment at end users 
premises. This guarantee covers only material defects 
and assumes normal care and maintenance according 
to Car-O-Liner specification.  

The guarantee assumes that: 

 

The equipment is correctly installed and inspected 
in accordance with current local laws and regula-
tions. 

 

The equipment has not been altered or rebuilt 
without prior written approval from Car-O-Liner. 

 

Genuine Car-O-Liner spare parts are used in any 
repairs and conducted by Car-O-Liner certified 
technician. 

 

Operation and maintenance have been carried out 
according to the instructions in this manual. 

All claims on warranty shall be notified through your 
authorized Car-O-Liner Distributor by use of Car-O-
Liner´s VisionWeb platform without undue delay and 
shall verify that the fault has occurred within the guar-
antee period and that the unit has been used within its 
operating range as stated in the specifications. All 

claims shall include the product type and article number 
as well as a detailed description of the problem and ac-
tions taken trying to solve it. This data is stamped on the 
name plate (refer to section 1.2 "Marking" for location). 

Note 

This instruction manual provides advice as well as in-
structions for installation, operation, maintenance and 
trouble shooting.  

IMPORTANT!   

Read this manual carefully to become 

familiar with the proper operation of the equipment. 
It is recommended that you use your authorized Car-O-
Liner Distributor for maintaining, servicing and upgrading 
your products. Never perform repairs, adjustments or any 
other work on the products which may result in personal 
injury and damage to the product. 

Your Car-O-Liner Distributor employs factory trained 
technicians and is focused on offering you the best overall 
experience with your new Car-O-Liner product. Any revi-
sions or upgrades of the products, as required by Car-O-
Liner, shall be performed by your authorized Car-O-Liner 
Distributor. 

The photographs and drawings in this manual are intend-
ed only to be illustrative and do not necessarily show the 
design of the equipment available on the market at any 
given time. The equipment is intended for use in accord-
ance with current trade practice, applicable laws and safe-
ty regulations. The equipment illustrated in the manual 
may be changed without prior notice. 

The contents in this publication can be changed without 
prior notice. 

This publication contains information which is protected 
by copyright laws. No part of this publication may be 
reproduced, stored in a system for information retrieval or 
be transmitted in any form, in any manner, without Car-
O-Liner’s prior written consent. 

 

Conformity with directives and standards 

The equipment is designed and manufactured by Car-O-
Liner, which is an EN-ISO 9001 and 14001 accredited 
development and manufacturing organisation. 

The equipment is CE-approved by Inspecta, Sweden. It is 
required that only Car-O-Liner approved spare parts and 
accessories are used with the equipment. 

Copyright  © Car-O-Liner AB, 2012 

Содержание BenchRack 4200
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды