manualshive.com logo in svg

Car-O-Liner BenchRack 4200, Инструкция по эксплуатации

Поделиться
Скачать
Car-O-Liner BenchRack 4200 Скачать руководство пользователя страница 40

 
 

 
 

Car-O-Liner Group AB 

BenchRack 

40

 

32163, EN- rev. 5,

 

2018-04

 

4.4.4 Bench 

mounting 

Please note that there are different types of bench mountings. 

If the vehicle is damaged so that it does not lie correctly in one or more of 
the chassis clamps, the following procedure is recommended: 

 

Lift the chassis clamp toward the sill edge with a suitable tool, then 
tighten the clamp against the sill edge. 

 

Tighten the chassis clamp bolts against the bench mounting, forcing 
the vehicle into the correct position. 

 

When all of the bolts have been properly tightened, alignment work 
can begin. 

During the course of the alignment work, distortion may be checked by loos-
ening the chassis clamp in question to see if the stress remains. 

 

IMPORTANT!

 When a wrench is used to tighten nuts and bolts, ensure that 

it is set to a maximum of 200 Nm to avoid damage to the equipment. 

 

IMPORTANT!

 All nuts and bolts shall be cleaned and greased regularly. 

 

Содержание BenchRack 4200
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды