manualshive.com logo in svg

Car-O-Liner BenchRack 4200, Инструкция по эксплуатации

Поделиться
Скачать
Car-O-Liner BenchRack 4200 Скачать руководство пользователя страница 28

 
 

 
 

Car-O-Liner Group AB 

BenchRack 

28

 

32163, EN- rev. 5,

 

2018-04

 

3.5.3 

Anchoring to the floor 

BenchRack must be anchored to the floor. 

WARNING!

 The lift must be bolted to the floor. Risk of tipping. 

 

Expander bolts M16x125, Car-O-Liners Art No. 36819. 
4 bolts (BR 4200, 5000 and 5500) or 6 bolts (BR 6300) are supplied with the 
bench system. See picture on the left for bolt positions. 

The lift should be anchored to a flat floor with the 
following properties: 

 

A minimum of K25 concrete floor quality. 

 

A minimum slab thickness of 150 mm (6 in). 

 

The requirements of the floor or the flatness of the floor (under the 
lifting platform) is 2 mm/m or better. 

Procedure 

Expander bolts M16x125, Car-O-Liners Art No. 36819. 4 bolts are supplied 
with the BenchRack system. 

Drill holes in the floor using the base plate holes as a template. Drill diame-
ter 16 mm (

⅔

 in), hole depth 110-120 mm (4-5 in). 

1

 

Clean the holes with vaccum cleaner and air hose. Unscrew the nut 
so that only the un-threaded top of the bolt is above the nut.  
Gently tap the expander bolts into the holes with a hammer. 

2

 

Tighten the bolts with a torque wrench set to 100 Nm. 

 

NOTE!

 If the above torque is not attained, the anchorage is not satisfactory. 

IMPORTANT!

 If there is any uncertainty about the quality of the floor, 

contact a building engineer for an inspection. 

 

IMPORTANT!

 It is the responsibility of the owner (user) of the equipment 

to ensure that inspection, in accordance with current local regulations, is 
carried out before the lift is put into use. 

X2, 
BR 6300 

X2 

X4, All 
benches 

X4 

X4 

X4 

Содержание BenchRack 4200
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды