Canon imageFORMULA DR-G2140 Скачать руководство пользователя страница 86

Страница: 86 / 196

3-24

CHAPTER 3 DISASSEMBLY & REASSEMBLY

V. UPPER UNIT-3 (READING RELATION)

1. Upper Reading Unit

1) Remove the eject tray unit.

(Page 3-7)

2) Remove the screw



(M3-bind head,

round tip) and remove the grounding ca-

ble



and connector



. And then

remove the locked cable band



, and

connector



Figure 3-501

3) Remove the registration upper roller.

(Page 3-13)

4) Remove 4 screws



(2 on both sides,

M3-TP head, round tip). While holding the

reading unit



, remove the right and left

guides



Note

: The right and left guides are the same

one.

Figure 3-502

5) Slide the reading unit



in front and hold

it. Remove 2 fitting parts



and remove

the cover



. And then remove the cable

band with lock



and remove the con-

nectors



and



. And remove the

reading unit with cables for the motor,

grounding and sensor.

Note:

Do not pull it excessively because a ca-

ble is connected.

Содержание imageFORMULA DR-G2140





































































































































































































Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы:

Canon imageFORMULA DR-G2140, Руководство по обслуживанию, Страница: 86 / 196

Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы: