Canon imageFORMULA DR-G2140 Скачать руководство пользователя страница 174

Страница: 174 / 196

5-40

CHAPTER 5 TROUBLESHOOTING

I. Other Function
1. Obtainment of Log Files

This is not function of the service tool.

However, the software for this machine auto-

matically collects log files of user usage sta-

tus information, and it is equipped with a func-

tion for obtainment of the log files.

Since the log files are designed to be use-

ful for resolving problems, the user may be

asked to do the operation to obtain the files.

The following gives an overview of the log

files and the procedure for recovering them.



Use of software and select screen

CaptureOnTouch “Environmental Settings”

2) CapturePerfect

“Version Information”

3) Scanner driver

“About”

4) Canon imageFORMULA Driver Setting

Tool

“Diagnostic”

Note:

Using the application software, you can
get its application and driver’s logs. Us-
ing the driver, you can get driver’s log.



Types of information

1) User operations

2) Error

3) Settings

4) Debugging

(Note that this excludes default settings)

5) Latest information when recovering the

files

The “Canon imageFORMULA Driver Set-

ting Too

l” is used for description following.

The settings of this tool are valid while USB

connection.



Procedure

1) Start “Canon imageFORMULA Driver Set-

ting tool” and open [Diagnostic]

tab.

Figure 5-279

2) Click the [Save] button for the [Output the

log file].

Figure 5-280

3) The Save Settings screen is displayed. Se-

lect the appropriate location to save the

files.

4) The files are saved with [xxx.dat] attached.



Log output level

Select [Standard] or [Full] of log file level.

Figure 5-281

Содержание imageFORMULA DR-G2140





































































































































































































Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы:

Canon imageFORMULA DR-G2140, Руководство по обслуживанию, Страница: 174 / 196

Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы: