Canon imageFORMULA DR-G2140 Скачать руководство пользователя страница 21

Страница: 21 / 196

1-13

CHAPTER 1 GENERAL DESCRIPTION

10) When the output has finished, a popup

window will be displayed.

Figure 1-319

4. Paper Jam, Skew and Staple

Detection Handling

If a feeding error occurs during scanning,

the following message is displayed on the
display panel and feeding stops.

Note:

Refer to the “I. Error Display’ in Chap-
ter 5 for the details of error message
and error code.

Figure 1-320

When the paper jam, skew, staple or

double feed is detected, and any documents
remaining in the eject tray or scanner must
be removed.

Note:

Be  careful  removing  any  documents
remaining  inside  the  scanner. Other-
wise  document  could  be  damaged  or
unexpected injury from paper cuts may
occur.

Note:

Remove all documents remaining in-
side the scanner. Any torn paper re-
maining may cause paper jams or trou-
bles.

1) Remove any documents remaining in the

eject tray.

2) Pull and hold the open/close lever, and

open the unit smoothly until it stops.

Note:

When opening and closing the upper
unit, be careful not to get your fingers
caught.

Содержание imageFORMULA DR-G2140





































































































































































































Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы:

Canon imageFORMULA DR-G2140, Руководство по обслуживанию, Страница: 21 / 196

Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы: