Canon imageFORMULA DR-G2140 Скачать руководство пользователя страница 34

Страница: 34 / 196

2-8

CHAPTER 2 FUNCTION & OPERATION

2) Separation mode: Thin paper

Figure 2-107

Note 1:

The pickup motor rotates slower than ones at the separation mode

“Normal” or “High”.

Note 2:

The separation motor is energized to stay, but not to rotate.

Note 3:

At a high speed feeding, the eject motor rotates slowly at a gray zone and fast at

black zone. At a low speed feeding, it rotates slowly at a gray and black zone.

▽

Note 3

Down

END

Start

Note 2

Note 1

Tray motor

Pickup sensor

Pickup motor

Pickup U/D motor

Feed motor

Separation motor

Main motor

Regist. front sensor

Regist. middle sensor

Regist. back sensor

Back side reading

Front side reading

Eject motor

Exit sensor

Содержание imageFORMULA DR-G2140





































































































































































































Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы:

Canon imageFORMULA DR-G2140, Руководство по обслуживанию, Страница: 34 / 196

Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы: