Canon imageFORMULA DR-G2140 Скачать руководство пользователя страница 98

Страница: 98 / 196

3-36

CHAPTER 3 DISASSEMBLY & REASSEMBLY

14. Pre U-turn Lower Roller

1) Remove the right and left covers.

(Page 3-3)

(Page 3-5)

2) Remove the right and left belts.

(Page 3-31)

(Page 3-32)

3) For the pre U-turn lower roller



, remove

the stopper



, pulley



and pin



on the

right side. And open the fitting parts to re-

move the pulley



and pin



on the left

side, and bearing



on each side.

Note:

Do not lose the pin.

Figure 3-621

4) On the left side, move the shaft to the left

hole (bigger one), and then pull out the pre

U-turn lower roller



without any damage

on the rubber roller sections.

Figure 3-622



Notes on assembling

Adjust and insert the rubber roller sections

into the holes in the U-turn guide.

Содержание imageFORMULA DR-G2140





































































































































































































Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы:

Canon imageFORMULA DR-G2140, Руководство по обслуживанию, Страница: 98 / 196

Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы: