Canon imageFORMULA DR-G2140 Скачать руководство пользователя страница 123

Страница: 123 / 196

4-7

CHAPTER 4 INSTALLATION & MAINTENANCE

No.

Step

Details/Remarks

7 Connect the power cord and USB cable

Note

1) Inhere, the installation and operation

check will be done with the USB con-
nection.

2) This machine does not have a LAN ca-

ble, router and other goods related the
LAN connection in the box. You need
prepare separately.



Power cord

1) Connect the supplied power cord to the

power connector on the rear side of the
main body.



2) (100V model only) Connect the supplied

grand cord.



3) Insert the power plug in the receptacle.





USB cable

1) Connect the supplied USB cable with the

computer.

8 Turn the power ON and make the com-

puter recognize the scanner.

1) Press the power switch to turn this machine

ON.

2) Windows recognizes this machine as a new

hardware and installs it automatically.

3) When it was completed, The CaptureOn-

Touch icon appears on the taskbar as fol-
lows.

9 Ensure that it operates correctly by using

the supplied “CaptureOnTouch”. Refer to
the “User Manual” for details.

Содержание imageFORMULA DR-G2140





































































































































































































Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы:

Canon imageFORMULA DR-G2140, Руководство по обслуживанию, Страница: 123 / 196

Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы: