Canon imageFORMULA DR-G2140 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 196

Canon imageFORMULA DR-G2140 Скачать руководство пользователя страница 41

COPYRIGHT © CANON ELECTRONICS INC. 2018 CANON DR-G2140/G2110/G2090 FIRST EDITION

2-15

CHAPTER 2 FUNCTION & OPERATION

3. Separation Mechanism

The separation section consists the feed

roller, separation pad and retard roller. A
torque limiter is assembled in the retard roller.

When the overlapped documents have

been fed, the overlapped documents are
stopped at the separation pad, and if it does
not effect, the retard roller separates the over-
lapped documents.

The configuration of the separation

mechanism is shown below.



Separation pad separation (at Normal)

Figure 2-302



Retard roller separation (at Normal)

Figure 2-303

And 3 types of the separation mode are

available to adjust a kind of document.

1) Separation mode: Normal

This is good for the normal documents.
The  pickup  roller  downs  and  feeds  the
documents  with  a  normal  rotation.  And  it
stops rotations when the registration front
sensor detects a document.
The  feed  roller  rotates  normally,  and  the
retard roller stays without any rotation.
Therefore, the document only attaches the
feed roller side is fed to inside if the over-
lapped  documents  reach  at  the  retard
roller.
If one sheet of document reaches the sep-
aration  section,  the  retard  roller  rotates
with a following direction of feed roller and
document.

2) Separation mode: Thin paper

This  is  good  for  the  thin  documents  that
are easy to be jammed.
The  pickup  roller  downs  and  rotates  with
lower  speed  to  feed  the  documents.  And
the  pickup  roller  lifts  and  stop  rotations
when the registration front sensor detects
a document. It avoids rushing to feed the
documents.
Operations  of  the  feed  roller  and  retard
roller are the same as ones of the Normal
mode.

3) Separation mode: High

This is good for the sticky document that
are easy to be double feed.

Operations of the pickup roller and feed
roller are the same as ones of the Normal
mode.

The retard roller rotates with reverse direc-
tion till the registration front sensor detect
a document. It makes a separation harder.
When the registration front sensor detects
a document, the retard roller rotates with a
following direction of feed roller and docu-
ment.

«
...
39
40
41
42
43
...
»

Содержание imageFORMULA DR-G2140





































































































































































































Отзывы:

Нет отзывов