Canon imageFORMULA DR-G2140 Скачать руководство пользователя страница 96

Страница: 96 / 196

3-34

CHAPTER 3 DISASSEMBLY & REASSEMBLY

Figure 3-616

12. Platen Lower Roller

Note:

You need a short screwdriver. Other-

wise, you need to disassemble the

entire upper unit at first.

1) Remove the right and left covers.

(Page 3-3)

(Page 3-5)

2) Remove the lower entrance guide.

(Page 3-31)

3) Remove 2 screws



(M3, stepped 3.2),

and remove the lower feed guide



Figure 3-617

4) Remove 2 screws



(M3-bind head,

round tip) using a short screwdriver and re-

move the platen unit



Note:

The screwdriver may strike the upper

unit and may not touch the screw verti-

cally. Install and remove screws

carefully. It is better to use a short

screwdriver.

Содержание imageFORMULA DR-G2140





































































































































































































Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы:

Canon imageFORMULA DR-G2140, Руководство по обслуживанию, Страница: 96 / 196

Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы: