Canon imageFORMULA DR-G2140 Скачать руководство пользователя страница 72

Страница: 72 / 196

3-10

CHAPTER 3 DISASSEMBLY & REASSEMBLY

III. UPPER UNIT-1 (MECHANICAL RELATION)

1. Pickup Unit

1) Remove the eject tray unit.

(Page 3-7)

2) Remove the upper front cover.

(Page 3-8)

3) Open the pickup roller cover, and remove

2 screws



(M3x6, self-tapping) and the

screw



(M3-bind head, round tip) for

pickup sensor position adjustment.

Figure 3-301

4) Remove the cables



connected to the

pickup motor and pickup sensor.

Figure 3-302

5) Remove 3 cables



connected on the

main drive PCB.

Figure 3-303

4) Remove the screw



(M3-bind head,

round tip) and remove the ground plate



Then, remove 4 screws



(M3-TP head,

round tip) and remove the pickup unit



Figure 3-304



Notes on assembling

Finally, install the ground plate at the orig-

inal position, and tighten the screw



(M3-bind head, round tip) for pickup sen-

sor position adjustment which was

removed in step 3, to the extent that it does

not become loose. If they are tightened ex-

cessively, the position of the pickup sensor

Содержание imageFORMULA DR-G2140





































































































































































































Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы:

Canon imageFORMULA DR-G2140, Руководство по обслуживанию, Страница: 72 / 196

Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы: