Canon imageFORMULA DR-G2140 Скачать руководство пользователя страница 177

Страница: 177 / 196

5-43

CHAPTER 5 TROUBLESHOOTING

IV. OPERATION TROUBLESHOOTING

When an operation problem occurs, check the error message displayed on the display con-

nected to a computer. Also perform an operation check on the sensors and motors using the

service mode.

1. Power Does Not Turn ON

The display panel is mot lit.

Note:

Make sure to use the power cord supplied with the machine.

Cause/Faulty

Locations

Step

Check Item

Result

Action

power

supply

voltage

Is the power outlet sup-
plying power at the rated
voltage?

Explain to the user that this
is not a problem with the
machine.

Connection of power
cord

Is the power cord con-
nected?

Connect the power cord
correctly.

Power cord

Does a replacing the
power cord fix the prob-
lem?

YES

End.

Operation panel
Sub-drive PCB
Control PCB
Power PCB

Does the LED on the
control PCB light when
turn the power ON?

YES

Power is supplied.
Check the Step 6.

Check the step 5.

Is the cable connected?

YES

Check the step 6.

Connect the cable cor-
rectly.

Is the problem solved by
replacing the PCB?

YES

End.

Table 5-401

Содержание imageFORMULA DR-G2140





































































































































































































Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы:

Canon imageFORMULA DR-G2140, Руководство по обслуживанию, Страница: 177 / 196

Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы: