Canon imageFORMULA DR-G2140 Скачать руководство пользователя страница 150

Страница: 150 / 196

5-16

CHAPTER 5 TROUBLESHOOTING

The list is shown below.

Display

Details

Total

Total number of sheets fed.

LED

Total lit time of the LED for
the reading unit. This units is
in “seconds”. When you re-
placed, you have to input [0].

Jam 1

The number of paper jams in
the pickup section. Error
code P001.

Jam 2

The number of paper jams in
the registration section. Er-
ror code

P002/P006/P007.

Jam 3

Number of document jams in
the eject section. Error code
P004/P010.

Replacement

For user replaceable parts.
[1]



Pick Roller Kit

[2]



Separation pad

It is displayed the total num-
ber of sheets fed when reset
in user mode. When you re-
placed, you have to reset or
input [Total].

Replacement

For service periodically re-
placed parts.
[3]



Feeding rollers: ex-

pected life 8-million fed.
[4]



Platen rollers & Exit

drive  roller:  expected  life  6-
million fed.
It is displayed the total num-
ber  of  sheets  fed  when  you
replaced  the  parts.  When
you replaced, you have to in-
put [Total].

Replacement

Total operated time of the
power PCB. This units is in
“hours”. When you replaced,
you have to input [0].

Table 5-202

Note

: In the

user mode “Maintenance”, it is

displayed the number since the parts

was replaced.

These values are changed when the con-

trol PCB is replaced. After the replacing the

control PCB, input the same values as before
the replacement. If you don’t know the values
before the replacement, input the estimated

values.

When the “Edit” button on the information

screen is selected, values are displayed val-

idly and can be changed.

Figure 5-225

If the [Apply] button on the information

screen is selected, the values are saved.

And if the [Cancel] button is selected,

they are not saved.

Содержание imageFORMULA DR-G2140





































































































































































































Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы:

Canon imageFORMULA DR-G2140, Руководство по обслуживанию, Страница: 150 / 196

Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы: