Canon imageFORMULA DR-G2140 Скачать руководство пользователя страница 14

Страница: 14 / 196

1-6

CHAPTER 1 GENERAL DESCRIPTION

Precautions

This

section describes items that require

particular care, for example, regarding human

safety.

These precautions must be observed.

The user should be explained the items that re-

late to user safety and instructed to take appro-

priate actions.

1) Power OFF in emergency

If such abnormal conditions as extraordi-

nary

noise, smoke, heat and odor occur,

immediately unplug the power cord.

Be careful not to get clothing (ties, long

hair, etc.) caught in this machine as it may

cause injury. Should this occur, immedi-

ately unplug the power cord. Do not insert

fingers in the feed section while moving

the rollers.

2) Power OFF on disassembling

When disassembling and assembling are

performed, unplug the power cord.

3) Prohibition of modify

This machine must not arbitrarily be modi-

fied or remade. If it is, use of this machine

may be forcibly suspended.

To change the specifications or disassem-

ble and reassemble this machine, follow

the instructions described in this manual

and the service information.

4) Electromagnetic wave interference

This machine complies with some stand-

ards regarding electromagnetic wave in-

terference, such as VCCI and FCC. How-

ever, the user may have to take counter-

measures if the machine causes electro-

magnetic wave interference.

5) User Manual

Read each “User Manual” thoroughly prior
to use of this machine.

6) Disposal

Follow local regulations when disposing of

the product and parts. This product is sub-

ject to the WEEE Directive in Europe.

7) Movement

This machine weighs 25 kg. When lifting or

moving this machine, 2 persons must hold

it from both sides.

Never lift it by one per-

son.

Figure 1-102

Содержание imageFORMULA DR-G2140





































































































































































































Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы:

Canon imageFORMULA DR-G2140, Руководство по обслуживанию, Страница: 14 / 196

Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы: