Canon imageFORMULA DR-G2140 Скачать руководство пользователя страница 18

Страница: 18 / 196

1-10

CHAPTER 1 GENERAL DESCRIPTION

2) Document eject tray

Hold both document guides and adjust
the positions according to the width of the
document to be set.

Figure 1-304

Note:

The positions of the right and left docu-
ment guides of the document eject tray
can be changed independently of each
other.

Open the document eject tray extension
according to the document length. Raise
the document eject stopper as necessary.

Figure 1-305

2. Job Function

The job function select and executes

jobs  (favorites)  that  have  been  registered
with  CaptureOnTouch  by  pressing  the  job
key on the operation panel.

Refer to the “User Manual” for details.

1) Press the Job key on the operation panel.

Note:

With USB connection, the Job selection
screen is displayed. With LAN connec-
tion, the PC selection screen is dis-
played.

Figure 1-306

Figure 1-307 (USB)

Figure 1-308 (LAN)

Содержание imageFORMULA DR-G2140





































































































































































































Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы:

Canon imageFORMULA DR-G2140, Руководство по обслуживанию, Страница: 18 / 196

Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы: