Canon imageFORMULA DR-G2140 Скачать руководство пользователя страница 144

Страница: 144 / 196

5-10

CHAPTER 5 TROUBLESHOOTING

3. How to Start and Finish



How to start

1) Start the computer for servicing.

2) If an icon of CaptureOnTouch is displayed

on the task bar, click the icon to terminate.

Note:

Refer to the “User Manual” for the de-
tails of how to terminate CaptureOn-

Touch.

3) Connect the USB cable and then turn on

the machine.

4) Start up

the installed file “DRUnification-

Tool.exe”.

5) The password screen is displayed, so after

inputting the 6 characters

“market,” select

[OK].

Figure 5-205

6) The initial screen is displayed.

Figure 5-206

7) If you execute the service mode, select

[Select Scanner] and if you register the

firmware, select [Firm Registration].

8) When [Select Scanner] is selected, the

scanner selection screen is displayed. Se-

lect the connected scanner.

Figure 5-207

The “Information” screen is displayed.

Figure 5-208

Note:

Do not start up

any

other application

software such as CaptureOnTouch or

turn off the machine while the service

tool is running. If the tool becomes un-

responsive, you should restart the com-

puter.



How to finish

To finish the service tool, select [



:Close]

on each operation screen or select [End

Application] from [File] on the toolbar.

However, if “Firmware version update” is
performed, reset the power properly.

Содержание imageFORMULA DR-G2140





































































































































































































Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы:

Canon imageFORMULA DR-G2140, Руководство по обслуживанию, Страница: 144 / 196

Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы: