Canon imageFORMULA DR-G2140 Скачать руководство пользователя страница 75

Страница: 75 / 196

3-13

CHAPTER 3 DISASSEMBLY & REASSEMBLY



Notes on assembling

When mounting the coil spring in the bear-

ing holder, set the position of the spring

bending section



as follows. Insert the

end of the bending section between the

ball bearing flange



and the bearing

holder.

Since the end of the bending section

touches the outer area of the ball bearing,

static electricity on the roller is discharged

to the side plate.

Figure 3-309

Push the right and left bearing holders into

the side plate at the same time. Insert the

fitting part of the bearing holder into the

hole of the side plate.

5. Registration Upper Roller

1) While holding the upper middle feed

guide



, remove 3 screws



(M3,

stepped 3.2) and remove the upper middle

feed guide.

Figure 3-310

2) Open the end of both bearing holders



and while unhooking the fitting parts, re-

move the registration upper roller unit



Note:

Since the coil spring in the roller unit

may be detached, do not lose it.

Figure 3-311

Содержание imageFORMULA DR-G2140





































































































































































































Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы:

Canon imageFORMULA DR-G2140, Руководство по обслуживанию, Страница: 75 / 196

Результаты поиска

Содержание imageFORMULA DR-G2140

Отзывы: