Brother 893-Z05 Скачать руководство пользователя страница 91

Страница: 91 / 110

Pull up the holder to leave the blade in the
rubber area.

■

Installing

Grasp the shaft of the new blade, and then
insert it into the blade slot in the end of the
holder.

The blade shaft is held in place by a magnet in the
holder. Slowly insert the blade shaft, and then slowly
release it after the shaft snaps into place against the
magnet.

Twist on the holder cap to attach it to the
holder.

Fully tighten the cap until it can no longer be turned.

WARNING

• This is not a toy and is not intended to be used

by children. In order to prevent choking
hazards, do not allow infants/children to put the
protective cap in their mouths.

CAUTION

• After removing the blade holder from the

machine, be sure to attach the protective cap.

• Do not press the tip of the holder with your

hand or fingers because the tip of the blade will
extend and may result in injuries.

• Please remove protective cap from blade

holder before placing it into the machine
carriage.

• This is not a toy and is not intended to be used

by children. In order to prevent injury, do not
allow infants/children to touch the blade.

Содержание 893-Z05















































































































Результаты поиска

Содержание 893-Z05

Отзывы:

Похожие инструкции для 893-Z05

Бренды по названию

Популярные бренды

Brother 893-Z05, Руководство по эксплуатации

Результаты поиска

Содержание 893-Z05

Отзывы:

Похожие инструкции для 893-Z05

Бренды по названию

Популярные бренды