Brother 893-Z05 Скачать руководство пользователя страница 100

Страница: 100 / 110

Not all of the material to
be cut is cut. Some
areas remain uncut.

A blade appropriate for the material
being cut is not used.

Use a blade appropriate for the material
being cut.

page 23

If cutting is not possible even
though the cutting pressure is set
higher than necessary, the blade
may be chipped.

Replace the blade with a new one.

page 87

The mat’s adhesive strength has
decreased, or the material is not
secured.

Replace the mat with a new one.

page 87

The blade is worn.

Replace the blade with a new one.

page 87

The material is incompatible with
this machine.

Replace the material with one
compatible with this machine.

page 14

The cutting pressure (“Cut
Pressure”) is incorrect.

Adjust the setting for “Cut Pressure” in
the settings screen.

page 10
page 27

Dust or lint has accumulated in the
holder.

Clean the holder.

page 89

The spacing between arranged
patterns is too small.

Rearrange the patterns to slightly
separate them.
Set the number to “3” or higher in the
“Pattern Interval” setting, and then
rearrange the patterns or perform the
auto layout function.

page 10
page 49

The material or tape extends from
the adhesive area of the mat.

Attach the material or tape while keeping
it within the adhesive area of the mat.

page 16

Fabric was cut without using a
sheet for fabric cutting.

Attach a high tack adhesive fabric
support sheet to a mat or affix an iron-on
fabric appliqué contact sheet to a fabric
before cutting it.

page 17
page 20

A fabric is not firmly attached to a
mat that has a high tack adhesive
fabric support sheet on its
adhesive side.

Firmly attach the fabric to the mat
pressing the handle of the included
spatula across the surface of the fabric.

page 20

An iron-on fabric appliqué contact
sheet is not firmly attached to a
fabric.

Iron the entire contact sheet to affix it
firmly to the wrong side of the fabric.

page 17

There are deep cuts
completely through the
mat.

The cutting pressure (“Cut
Pressure”) is incorrect.

Adjust the setting for “Cut Pressure” in
the settings screen.

page 10
page 27

The material to be cut is
not cleanly cut.

After using a mat with deep cut
marks which completely went
through the mat, the machine's
surface where the blade points
down (

) has cut marks.

Contact the retailer who sold you this
machine or the nearest authorized
service center.

—

Symptom

Possible Causes (or Results)

Solutions

Reference

Содержание 893-Z05















































































































Результаты поиска

Содержание 893-Z05

Отзывы:

Похожие инструкции для 893-Z05

Бренды по названию

Популярные бренды

Brother 893-Z05, Руководство по эксплуатации

Результаты поиска

Содержание 893-Z05

Отзывы:

Похожие инструкции для 893-Z05

Бренды по названию

Популярные бренды