Broadcom BCM1125 Скачать руководство пользователя страница 496 | Manualshive

Страница: 496 / 516

background image

BCM1250/BCM1125/BCM1125H

User Manual

10/21/02

B r o a d c o m C o r p o r a t i o n

Page

468

Section 16: Reference

Document

1250_1125-UM100CB-R

ctcp_def_1

00_1002_0b98

CRC and checksum definition register.

dm_partial_0

00_1002_0ba0

CRC/Checksum partial result register.

dm_partial_1

00_1002_0ba8

CRC/Checksum partial result register.

dm_partial_2

00_1002_0bb0

CRC/Checksum partial result register.

dm_partial_3

00_1002_0bb8

CRC/Checksum partial result register.

zbbus_cycle_cp0

00_1002_0C00

ZBbus cycle count compare register zero.

zbbus_cycle_cp1

00_1002_0C08

ZBbus cycle count compare register one.

system_scratch

00_1002_0C10

Scratch register for software use

alias_mailbox_cpu_0

00_1002_1xx0

Alias of status of mailbox (has incomplete decode, so
access from pci won't hang). (Read Only).

alias_mailbox_set_cpu_0

00_1002_1xx8

Set bits in mailbox_cpu_0 by writing 1s to this location
(Write Only, has incomplete decode, so access from pci
won't hang).

int_mapper_1

00_1002_2000

2000-23f8 Registers for CPU 1 interrupt mapper (+2000
from CPU 0).

zbbus_cycle_cnt

00_1003_0000

ZBbus cycle count.

system_manuf

00_1003_8000

Read Only. Manufacturing Information Register.

l2_read_address

00_1004_0018

Read only. Last address/tag in a read (for testing)

l2_ecc_address

00_1004_0038

Read only. Last address with ecc error (correctable or
not).

l2_misc_value

00_1004_0058

Read only. PERIPH_REV3 and later. Value of L2 hidden
registers.

l2_way_disable

00_1004_1x00

Accesses made to this range of addresses will write the
value x to l2_wayen[3:0] register. If l2_wayen[i] is clear
Way i is removed from the L2 replacement algorithm.
See

Section: “Using the L2 Cache as

Memory” on page 91

l2_cache_disable

00_1004_2x00

Accesses made to this range of addresses will write the
value x to l2_cache_disable[3:0] register.
See

Section: “Reduced Cache Size” on page 94

l2_misc_config

00_1004_3x00

Accesses made to this range of addresses will write the
value x to l2_misc_config[3:0] register.
See

Section: “Cache Configuration Register” on page 99

.

mc_config_0

00_1005_1100

Channel 0 attributes.

mc_dramcmd_0

00_1005_1120

Channel 0 SDRAM command.

mc_drammode_0

00_1005_1140

Channel 0 SDRAM mode.

mc_timing1_0

00_1005_1160

Channel 0 SDRAM timing 1.

mc_timing2_0

00_1005_1180

Channel 0 SDRAM timing 2.

mc_cs_start_0

00_1005_11a0

Channel 0 CS[3:0] start address.

mc_cs_end_0

00_1005_11c0

Channel 0 CS[3:0] end+1 address.

mc_interleave_0

00_1005_11e0

Channel 0 interleaved CS position.

mc_cs0_row_0

00_1005_1200

Channel 0 CS0 row address bits.

Table 312: Internal Registers Ordered by Address

(Cont.)

Name

Address

Table/

Page

Description

«
...
494
495
496
497
498
...
»

Содержание BCM1125





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BCM1125

Express EtherNetwork DFE-670TXD

Бренд: D-Link Страницы: 4

Бренд: DAD Страницы: 36

Бренд: D-Link Страницы: 2

Бренд: CAME Страницы: 19

Бренд: Supero Страницы: 68

Duinotech Lilypad Plus XC3920

Бренд: Jaycar Electronics Страницы: 2

Speedway Revolution

Бренд: impinj Страницы: 60

Бренд: Aaeon Страницы: 61

Бренд: Rajant Corporation Страницы: 40

Бренд: B&B Electronics Страницы: 17

Бренд: Quadram Страницы: 21

TeleMyo 2400T V2

Бренд: Noraxon Страницы: 52

Бренд: Inspired Energy Страницы: 5

Бренд: ANTAIRA Страницы: 6

Бренд: Allied Telesis Страницы: 44

Бренд: LevelOne Страницы: 61

Бренд: Maco Страницы: 8

Бренд: Aaeon Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды