manualshive.com logo in svg

Broadcom BCM1125, Руководство пользователя

Broadcom BCM1125 - высокопроизводительный процессор, обеспечивающий быструю и эффективную работу устройства. Чтобы ознакомиться с руководством пользователя, вы можете бесплатно скачать его с нашего сайта. Узнайте больше о вашем устройстве, загрузив руководство по эксплуатации на manualshive.com.

Поделиться
Скачать
background image

BCM1250/BCM1125/BCM1125H

User Manual

10/21/02

B r o a d c o m   C o r p o r a t i o n

Page  

286

Section 9: Ethernet MACs

 Document

1250_1125-UM100CB-R

M

ANAGEMENT

 I

NTERFACE

 

TO

 PHY

There is a simple serial management interface between the MAC and the PHY device (or devices). It supports
up to 32 PHY chips (although some PHY devices attach special meaning to address 0) each of which have 32
16-bit registers.

The CPU runs the serial protocol through reading and writing the 

mac_mdio

 register. 

The management data clock (MDC) is generated by the interface and is an input to the PHY. Data written to
the mdc bit in the 

mac_mdio

 register is put out on the MDC pin. 

The management data i/o line (MDIO) can be driven by either the MAC or the PHY. It should have an external
1.5K pull-up resistor to pull the line to a 1 when neither is driving. The state of the pin can always be read on
the mdio_in bit in the 

mac_mdio

 register. The interface can drive the line by clearing the mdio_dir bit and

writing the data to output to the mdio_out bit. 

The MDIO data is latched by the PHY on the rising edge of MDC, so the mdio_dir and mdio_out bits should
never be changed when the mdc bit is changed from a zero to a one. To send data to the PHY the mdio_dir
bit should be cleared, a single write to the 

mac_mdio

 register can be used to set mdc low and put the data on

mdio_out. The same data should be written to mdio_out when mdc is set high. 

There is a general purpose output pin (GENO) associated with each MAC that is also controlled through the

mac_mdio

 register. This pin is not part of the standard G/MII connection.

Each MAC interface has its own set of MDIO/MDC/GENO pins. This allows the MAC drivers to be completely
independent with no shared resources, which works well in designs where the MACs are partitioned across
the processors with each running its own operating system. In a system running a single operating system (or
where all the MACs are controlled from a single driver) the PHY addressing scheme can be used to attach the
PHYs for all three MACs to the MDIO/MDC lines of a single MAC. In this case the other MDC lines become
available as general outputs, and the other MDIO lines as GPIOs.

Содержание BCM1125





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BCM1125

D-Link xStack Storage DSN-4000 Series Datasheet preview
xStack Storage DSN-4000 Series
Бренд: D-Link Страницы: 5
Lanner ICS-P570 User Manual preview
ICS-P570
Бренд: Lanner Страницы: 63
Moxa Technologies TAP-125 Series User Manual preview
TAP-125 Series
Бренд: Moxa Technologies Страницы: 51
Kaptia Klever Getting Started preview
Klever
Бренд: Kaptia Страницы: 14
Uniflair PCOWeb Instruction Manual preview
PCOWeb
Бренд: Uniflair Страницы: 24
National Instruments SC-2040 User Manual preview
SC-2040
Бренд: National Instruments Страницы: 56
EZCast Pro Dongle II User Manual preview
Pro Dongle II
Бренд: EZCast Страницы: 24
3Com FEM656C Quick Start Manual preview
FEM656C
Бренд: 3Com Страницы: 53
2N Telekomunikace ATEUS STARGATE User Manual preview
ATEUS STARGATE
Бренд: 2N Telekomunikace Страницы: 67
Uctronics U6180 Instruction Manual preview
U6180
Бренд: Uctronics Страницы: 2
Cutting Edge Unity AM Manual preview
Unity AM
Бренд: Cutting Edge Страницы: 92
National Instruments PXI-GPIB Getting Started preview
PXI-GPIB
Бренд: National Instruments Страницы: 45
Inter-m S- Media Manual preview
S- Media
Бренд: Inter-m Страницы: 20
AXIOMTEK IPC934-230-FL Quick Installation Manual preview
IPC934-230-FL
Бренд: AXIOMTEK Страницы: 2
NovaStar Nova M3 MFN300 Operation Manual preview
Nova M3 MFN300
Бренд: NovaStar Страницы: 16
DMX4ALL DMX-Relais 2 INRUSH User Manual preview
DMX-Relais 2 INRUSH
Бренд: DMX4ALL Страницы: 18
National Datacomm 9210S01 User Manual preview
9210S01
Бренд: National Datacomm Страницы: 62
Advantage Boost Box Setup Manual preview
Boost Box
Бренд: Advantage Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды