manualshive.com logo in svg

Broadcom BCM1125, Руководство пользователя

Broadcom BCM1125 - высокопроизводительный процессор, обеспечивающий быструю и эффективную работу устройства. Чтобы ознакомиться с руководством пользователя, вы можете бесплатно скачать его с нашего сайта. Узнайте больше о вашем устройстве, загрузив руководство по эксплуатации на manualshive.com.

Поделиться
Скачать
background image

BCM1250/BCM1125/BCM1125H

User Manual

10/21/02

B r o a d c o m   C o r p o r a t i o n

Page  

310

Section 9: Ethernet MACs

 Document

1250_1125-UM100CB-R

6 

rx_ch0_derr 

1’b0 

Set if any error is marked on data returned by a read. The channel will be stopped. 
Software must disable and re-enable the channel to clear this fault. 

7

rx_ch0_drop

1’b0 

Set if a packet was dropped because there were no descriptors available when the 
start of packet was received. (If there are descriptors available for the start of 
packet, but the controller runs out of descriptors during the packet reception then 
the dscr_err bit will be set in the receive status word for the packet.) The interface 
will continue dropping data until there are descriptors available when a start of 
packet is received.

8

rx_ch1_eop_count 

1’b0 

Set if the EOP interrupt was raised as a result of the packet count being reached. 

9

rx_ch1_eop_timer 

1’b0

Set if the EOP interrupt was raised as a result of the packet timer triggered. 

10

rx_ch1_eop_seen 

1’b0 

Set at the end of any packet transfer. It can be used during polling to determine if 
any packets have been transferred since the register was read (regardless of the 
setting of the int_pktcnt field). 

11

rx_ch1_hwm 

1’b0

This bit will be set if the current descriptor count is less than the high watermark. 
This bit is not latched (see bit 3).

12

rx_ch1_lwm 

1’b0 

This bit will be set if the current descriptor count is less than the low watermark. 
This bit is not latched (see bit 3). 

13

rx_ch1_dscr 

1’b0 

Set if the interrupt is triggered by a descriptor with the interrupt bit set. 

14

rx_ch1_derr 

1’b0 

Set if any error is marked on data returned by a read. The channel will be stopped. 
Software must disable and re-enable the channel to clear this fault. 

15

rx_ch1_drop

1’b0 

Set if a packet was dropped because there were no descriptors available when the 
start of packet was received. (If there are descriptors available for the start of 
packet, but the controller runs out of descriptors during the packet reception then 
the dscr_err bit will be set in the receive status word for the packet.) The interface 
will continue dropping data until there are descriptors available when a start of 
packet is received.

16

tx_ch0_eop_count 

1’b0 

Set if the EOP interrupt was raised as a result of the packet count being reached. 

17

tx_ch0_eop_timer 

1’b0

Set if the EOP interrupt was raised as a result of the packet timer triggered. 

18

tx_ch0_eop_seen 

1’b0 

Set at the end of any packet transfer. It can be used during polling to determine if 
any packets have been transferred since the register was read (regardless of the 
setting of the int_pktcnt field). 

19

tx_ch0_hwm 

1’b0

This bit will be set if the current descriptor count is less than the high watermark. 
This bit is not latched (see bit 3).

20

tx_ch0_lwm 

1’b0 

This bit will be set if the current descriptor count is less than the low watermark. 
This bit is not latched (see bit 3).

21

tx_ch0_dscr

1’b0 

Set if the interrupt is triggered by a descriptor with the interrupt bit set. 

22

tx_ch0_derr

1’b0 

Set if data marked with an error is returned for any read (descriptor or data buffer). 
The channel will be stopped. Software must disable and re-enable the channel to 
clear this fault.

23

tx_ch0_dzero

1’b0 

Set if a descriptor has a packet length of zero or the SOP flag bit is not set in the 
first descriptor of a packet. This bit is also set if the controller runs out of descriptors 
during a packet transmission. The channel will be stopped. Software must disable 
and re-enable the channel to clear this fault.

24

tx_ch1_eop_count 

1’b0 

Set if the EOP interrupt was raised as a result of the packet count being reached. 

25

tx_ch1_eop_timer 

1’b0

Set if the EOP interrupt was raised as a result of the packet timer triggered. 

Table 182:  MAC Status Registers

 (Cont.)

mac_status_0 - 

00_1006_4408

mac_status_1 - 

00_1006_5408

mac_status_2 - 

00_1006_6408

READ ONLY - Reading this register will clear all latched bits

This register is used in both Ethernet and Packet FIFO modes

Bits

Name

Default

Description

Содержание BCM1125





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BCM1125

Magnat Audio MC 200 Faq preview
MC 200
Бренд: Magnat Audio Страницы: 2
Cabletron Systems Netlink FRX4000 Installation And Setup Manual preview
Netlink FRX4000
Бренд: Cabletron Systems Страницы: 8
Cabletron Systems 9C300-1 Upgrade Instructions preview
9C300-1
Бренд: Cabletron Systems Страницы: 4
Sun Microsystems Ray 3 Plus Client Getting Started Manual preview
Ray 3 Plus Client
Бренд: Sun Microsystems Страницы: 6
Lanner NCA-4035 User Manual preview
NCA-4035
Бренд: Lanner Страницы: 109
C&H Active Module Carrier VX402C-64 User Manual preview
Active Module Carrier VX402C-64
Бренд: C&H Страницы: 32
NEC Thin Client US310e Getting Started preview
Thin Client US310e
Бренд: NEC Страницы: 6
Supermicro Optane Persistent Memory 200 Series User Manual preview
Optane Persistent Memory 200 Series
Бренд: Supermicro Страницы: 54
Hauppauge WinTV USB Installation And Reference Manual preview
WinTV USB
Бренд: Hauppauge Страницы: 55
Echo LAYLA 3G Owner'S Manual preview
LAYLA 3G
Бренд: Echo Страницы: 21
Data Translation DT9835 Getting Started Manual preview
DT9835
Бренд: Data Translation Страницы: 62
Thermalright Macho Rev. A (BW) Manual preview
Macho Rev. A (BW)
Бренд: Thermalright Страницы: 32
Xtreme SNMP-R90 User & Installation Manual preview
SNMP-R90
Бренд: Xtreme Страницы: 83
CoolShirt IB-400 Operating Instructions preview
IB-400
Бренд: CoolShirt Страницы: 3
Patton electronics ForeFront 2616RC Getting Started Manual preview
ForeFront 2616RC
Бренд: Patton electronics Страницы: 80
Barco S3 series User Manual preview
S3 series
Бренд: Barco Страницы: 538
Bdcom GP3600-16 Hardware Installation Manual preview
GP3600-16
Бренд: Bdcom Страницы: 25
EDT PCIe Gen1 Framegrabbers User Manual preview
PCIe Gen1 Framegrabbers
Бренд: EDT Страницы: 43

Бренды по названию

Популярные бренды

Загрузить еще бренды