manualshive.com logo in svg

Broadcom BCM1125, Руководство пользователя

Broadcom BCM1125 - высокопроизводительный процессор, обеспечивающий быструю и эффективную работу устройства. Чтобы ознакомиться с руководством пользователя, вы можете бесплатно скачать его с нашего сайта. Узнайте больше о вашем устройстве, загрузив руководство по эксплуатации на manualshive.com.

Поделиться
Скачать
background image

BCM1250/BCM1125/BCM1125H

User Manual

10/21/02

B r o a d c o m   C o r p o r a t i o n

Page  

354

Section 10: Serial Interfaces

 Document

1250_1125-UM100CB-R

6

rx_edge_det

1’b0

[7:6]These two bits set the interface synchronization method.
00: External Enable is used using level as frame start. 
01: External Enable is used, using edge as frame start.
10: Internal table drives enable, sync is level sensitive.
11: Internal table drives enable, sync is edge sensitive.

7

rx_table_en

1’b0

8

tx_clk_inv

1’b0

This bit contols the inverter on the transmit clock.
0: Not inverted (clock on rising edge).
1: Inverted (clock on falling edge).

9

tx_clk_src

1’b0

Transmitter clock source.
0: Internal clock, generated by the baud rate generator.
1: External clock from RCLKIN pin.

11:10

tx_sync_delay

2’b0

Number of clock delays between the Frame Sync/Enable and the first bit of the 
frame.

12

tx_sync_active

1’b0

0: Sync/Enable is active high.
1: Sync/Enable is active low.

13

tx_strobe_active

1’b0

0: Strobe in Line Interface is active high.
1: Strobe in Line Interface is active low.

14

tx_edge_det

1’b0

[15:14]These two bits set the interface synchronization method.
00: External Enable is used using level as frame start. 
01: External Enable is used, using edge as frame start.
10: Internal table drives enable, sync is level sensitive.
11: Internal table drives enable, sync is edge sensitive.

15

tx_table_en

1’b0

63:16

notimp

48’bx

Not implemented.

Table 232:  Synchronous Serial Clock Source and Line Interface Mode Register

 (Cont.)

ser_line_mode_0 - 

00_1006_0578

ser_line_mode_1 - 

00_1006_0978

Bits

Name

Default

Description

Table 233:  Synchronous Serial Command Register (Write-only)

ser_cmd_0 - 

00_1006_0540

ser_cmd_1 - 

00_1006_0940

Bits

Name

Description

0

rx_en

Receive enable.  When the receiver is reset, writing a one enables the receiver.

1

tx_en

Transmit enable.  When the transmitter is reset or paused, writing a one enables the transmitter.

2

rx_reset

Receive reset.  Writing a one resets the receiver. This should only be done when the line is idle 
or being restarted, resetting an active interface can result in partial packet reception. Writing 
this bit will only reset the state machines; configuration registers are not returned to their default 
values.

3

tx_reset

Transmit reset.  Writing a one resets the transmitter. This should only be done when the line is 
idle or being restarted, resetting an active interface can result in UNPREDICTABLE data and 
strobe signals being generated. Writing this bit will only reset the state machines; configuration 
registers are not returned to their default values.

4

reserved

Must be written as 0.

5

tx_pause

Transmit pause.  Writing a one causes the transmitter to pause at the end of the next packet. 
If the transmitter has no data it will stop immediately, otherwise it will continue sending until the 
next end of packet has been sent. The transmitter leaves any subsequent packet in the TxFIFO. 
When the transmitter is re-enabled (by writing a 1 to the tx_en bit) the next packet will be fetched 
from the TxFIFO and normal operation will continue.

15:4

reserved

Must be written as 0.

63:16

notimp

Not implemented.

Содержание BCM1125





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BCM1125

Accusys ACS-76500 Owner'S Manual preview
ACS-76500
Бренд: Accusys Страницы: 34
Ruckus Wireless ZoneFlex 7731 Getting Started Manual preview
ZoneFlex 7731
Бренд: Ruckus Wireless Страницы: 56
Renesas RSKH836079 Quick Start Manual preview
RSKH836079
Бренд: Renesas Страницы: 6
Blackmagicdesign Teranex 2D Processor Installation And Operation Manual preview
Teranex 2D Processor
Бренд: Blackmagicdesign Страницы: 969
Enterasys Enterasys Matrix 2G4082-25 Hardware Installation Manual preview
Enterasys Matrix 2G4082-25
Бренд: Enterasys Страницы: 58
Lanner NCA-1040 User Manual preview
NCA-1040
Бренд: Lanner Страницы: 59
Riverbed SteelCentral AppResponse 2180 Upgrade And Maintenance Manual preview
SteelCentral AppResponse 2180
Бренд: Riverbed Страницы: 82
ZiLOG Z8018 Series User Manual preview
Z8018 Series
Бренд: ZiLOG Страницы: 317
Eagle Technology PC104PLUS-26 User Manual preview
PC104PLUS-26
Бренд: Eagle Technology Страницы: 39
Waveshare High-Precision AD/DA Board User Manual preview
High-Precision AD/DA Board
Бренд: Waveshare Страницы: 8
ETAS ES1337.2 User Manual preview
ES1337.2
Бренд: ETAS Страницы: 29
Dahua Technology NVR2104/2108HS-W-4KS2 1U User Manual preview
NVR2104/2108HS-W-4KS2 1U
Бренд: Dahua Technology Страницы: 363
Uctronics U6180 Instruction Manual preview
U6180
Бренд: Uctronics Страницы: 2
Balluff BIS C-489-1 KBT02 Series Technical Manual preview
BIS C-489-1 KBT02 Series
Бренд: Balluff Страницы: 74
Abov A34M418YLN User Manual preview
A34M418YLN
Бренд: Abov Страницы: 8
ADLINK Technology cPCI-8586 User Manual preview
cPCI-8586
Бренд: ADLINK Technology Страницы: 29
Extron electronics Network Device PIP 444 User Manual preview
Network Device PIP 444
Бренд: Extron electronics Страницы: 62
COMMUNICATIONS-APPLIED TECHNOLOGY ICRI Setup And Operating Procedures preview
ICRI
Бренд: COMMUNICATIONS-APPLIED TECHNOLOGY Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды