manualshive.com logo in svg

Broadcom BCM1125, Руководство пользователя

Broadcom BCM1125 - высокопроизводительный процессор, обеспечивающий быструю и эффективную работу устройства. Чтобы ознакомиться с руководством пользователя, вы можете бесплатно скачать его с нашего сайта. Узнайте больше о вашем устройстве, загрузив руководство по эксплуатации на manualshive.com.

Поделиться
Скачать
background image

User Manual

BCM1250/BCM1125/BCM1125H

10/21/02

B r o a d c o m   C o r p o r a t i o n

Document

1250_1125-UM100CB-R

Section 8: PCI Bus and HyperTransport Fabric Page  

239

Table 128:  PCI Command Register - Offset 4 Bits [15:0]

Bits

Name

Default

Description

0

IoSpaceEn

R/O 1’b0

I/O Space Enable. This bit is always zero. The bridge never accepts I/O space 
accesses from the PCI bus.

1

MemSpaceEn

R/W 1’b1

RevId>=3

R/W 1’b0

Memory Space Enable. This bit must be set to allow the bridge to accept memory 
space accesses from the PCI bus and forward them to either ZBbus or the 
HyperTransport bridge.
In interface revisions 1 and 2 this bit defaults to 1 to enable these accesses after 
reset, in interface revision 3 and greater this bit defaults to 0 to match the PCI 
specification.

2

MasterEn

R/W 1’b0

Bus Master Enable. This bit must be set to allow the bridge to act as a master on 
the PCI bus. This bit should be set before any PCI accesses are made. Any 
accesses to the PCI space that are received while this bit is clear will result in 
UNDEFINED behavior in the interface.

3

SpecCycEn

R/O 1’b0

The bridge does not accept Special Cycles, so this bit is always zero.

4

MemWrInvEn

R/W 1’b0

This bit should be set to allow the bridge to generate Memory Write and Invalidate 
commands. The bridge will only use Write Invalidate if the start address is 
cacheline aligned and the transfer is at least one cache line long (using the cache 
line size set in the ClineSz register).
If the latency timer expires while a Write Invalidate command is in progress the 
access will only be terminated at the next cache line boundary.

5

VgaPalSnpEn

R/O 1’b0

This bit is always zero. The bridge does not snoop VGA palette accesses.

6

ParErrResp

R/W 1’b0

This bit controls the response to PCI parity errors. If it is set then the MstrDParErr 
bit is set in the status register and the PCI error interrupt is raised when a parity 
error is detected. If it is clear then no interrupt is raised. In both cases the DetParErr 
bit is set in the status register.
A parity error resulting from a read will return data to the ZBbus with a bus error if 
this bit is set, and returned as valid data if this bit is clear.

7

StepCtrl

R/O 1’b0

This bit is always clear. The bridge does not do address/data stepping.

8

SerrEn

R/W 1’b0

SERR enable. If this bit is set, the bridge will drive the SERR_L pin if it detects a 
fatal error. If clear the bridge will never drive SERR_L.

9

FastB2BEn

R/O  1’b0

This bit is always clear. The bridge will never do fast back-to-back cycles to different 
devices.

15:10

reserved

R/O 6’b0

Reserved

Table 129:  PCI Status Register - Offset 4 Bits [31:16]

Bits

Name

Default

Description

3:0

reserved

R/O 4’b0

Reserved

4

CapList

R/O 1’b0

Always clear. There is no capabilities list.

5

66MHzCap

R/O 1’b1

This bit is set. The PCI is 66 MHz capable.

6

reserved

R/O 1’b0

Reserved

7

FastB2BCap

R/O 1’b1

This bit indicates that the bridge can accept fast back-to-back transactions when 
the transactions are to different agents.

8

MstrDParErr

R/C 1’b0

This bit is set if the bridge was a bus master and detected a parity error on read 
data, or was signalled that a parity error happened on write data. The ParErrEn bit 
in the command register must be set to allow this bit to be set. If this bit is set the 
PCI error interrupt is asserted. It is cleared by software writing a 1.

10:9

DevselTiming

R/O 2’b01

The bridge generates medium DEVSEL timing.

Содержание BCM1125





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BCM1125

Barracuda Networks Network Quick Start Manual preview
Network
Бренд: Barracuda Networks Страницы: 2
Pima ZEL508 Installation Instructions preview
ZEL508
Бренд: Pima Страницы: 4
LogLogic LX 1010 Quick Start Manual preview
LX 1010
Бренд: LogLogic Страницы: 30
LevelOne FPC-0103T Manual preview
FPC-0103T
Бренд: LevelOne Страницы: 31
Ubiquiti PowerBeam AC Gen2 Quick Start Manual preview
PowerBeam AC Gen2
Бренд: Ubiquiti Страницы: 22
LGC wireless InterReach Fusion SingleStar Installation And Operation Manual preview
InterReach Fusion SingleStar
Бренд: LGC wireless Страницы: 154
Daedalon EC-33 Instruction Manual preview
EC-33
Бренд: Daedalon Страницы: 6
IDT Tsi310TM User Manual preview
Tsi310TM
Бренд: IDT Страницы: 207
Cisco MERAKI MX450 Installation Manual preview
MX450
Бренд: Cisco MERAKI Страницы: 4
HighPoint RocketCache 3240X8 User Manual preview
RocketCache 3240X8
Бренд: HighPoint Страницы: 17
Multitech ISI608PC Owner'S Manual preview
ISI608PC
Бренд: Multitech Страницы: 81
Cypress Semiconductor CY8C24223A Specification Sheet preview
CY8C24223A
Бренд: Cypress Semiconductor Страницы: 31
AES BeBoPr++ User Manual preview
BeBoPr++
Бренд: AES Страницы: 44
Uctronics U6187 Assembly Manual preview
U6187
Бренд: Uctronics Страницы: 12
Intel SRCSASPH16I - RAID Controller Hardware Manual preview
SRCSASPH16I - RAID Controller
Бренд: Intel Страницы: 28
FDI USB-ICP-SAB9 Quick Start Manual preview
USB-ICP-SAB9
Бренд: FDI Страницы: 15
Intel SL6NQ - Xeon 2.4 GHz/533MHz/512 KB CPU Processor 2.4GHz Specification preview
SL6NQ - Xeon 2.4 GHz/533MHz/512 KB CPU Processor 2.4GHz
Бренд: Intel Страницы: 56
Roland Session SR-JV80-09 Owner'S Manual preview
Session SR-JV80-09
Бренд: Roland Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды